Toro TimeCutter Z Series Скачать руководство пользователя страница 8

Страница: 8 / 118

SPECIFICATIONS

1 - 4

TimeCutter™ Z Service Manual

Specifications

Z16-44

Z17-44

ENGINE:

High Idle 3400 ± 100 RPM

3400 ± 100 RPM

Low Idle 1400 RPM

1400 RPM

Manufacturer Briggs & Stratton

Kohler

Horsepower (kW) 16.5 HP (12.3kW) @ 3600 RPM

17 HP (12.7 kW) @ 3600 RPM

Fuel Unleaded Gasoline 87 octane min.

Unleaded Gasoline 87 octane min.

FUEL SYSTEM:

Capacity 5 Gallon (18.9 L)

5 Gallon (18.9 L)

TRACTION SYSTEM:

Transaxles Twin Hydro-Gear IZT Hydrostatic

Transaxles

Twin Hydro-Gear IZT Hydrostatic
Transaxles

Transaxle Drive Belt drive with self-tensioning system

Belt drive with self-tensioning system

Ground Speed Infinite, 0 to 6.5 MPH (10.5-km/hr) forward

0 to 3.4 MPH (5.5-km/hr) reverse

Infinite, 0 to 6.5 MPH (10.5-km/hr) forward
0 to 3.4 MPH (5.5-km/hr) reverse

TIRES:

Rear Drive Tires 18x10-8 4 ply with “Multitrac CS” Tread

18x10-8 4 ply with “Multitrac CS” Tread

Front Caster Tires 410/350 x 4 - 4.25 IS with “sawtooth” tread 410/350 x 4 - 4.25 IS with “sawtooth” tread

Tire Pressure 13 psi (90 kPa) rear, 35 psi (241 kPa) front 13 psi (90 kPa), rear 35 psi (241 kPa) front

ELECTRICAL
SYSTEM:

Battery Voltage 12 volt, negative ground

12 volt, negative ground

Battery Type BCI Group U1

BCI Group U1

DIMENSIONS:

Wheel Base 52.1 in. (132.3 cm) center of caster to

center of drive tires

52.1 in. (132.3 cm) center of caster to
center of drive tires

Overall Width 55 in. (139.7 cm) with deck deflector down

46.6 in. (118.4 cm) gate width with deck
deflector up

55 in. (139.7 cm) with deck deflector down

46.6 in. (118.4 cm) gate width with deck
deflector up

Overall Length 77.5 in. (196.9 cm)

77.5 in. (196.9 cm)

WEIGHT:

Net Weight 635 lbs. (approx.)

635 lbs. (approx.)

HEIGHT OF CUT:

Adjusts from 1.5” (3.8 cm) to
4.5” (11.4 cm) (7 positions)

Содержание TimeCutter Z Series























































































































Результаты поиска

Содержание TimeCutter Z Series

Отзывы:

Похожие инструкции для TimeCutter Z Series

Бренды по названию

Популярные бренды

Toro TimeCutter Z Series, Руководство по обслуживанию

Результаты поиска

Содержание TimeCutter Z Series

Отзывы:

Похожие инструкции для TimeCutter Z Series

Бренды по названию

Популярные бренды