manualshive.com logo in svg

Toro TimeCutter HD ZX4800, Руководство оператора

Поделиться
Скачать
Toro TimeCutter HD ZX4800 Скачать руководство пользователя страница 18

distance (twice the width of the machine) between
the machine and any hazard. Use a walk behind
machine or a hand trimmer to mow the grass in
these areas.

g229111

Figure 11

1.

Safe Zone-Use the mower here on slopes less than 15
degrees

2.

Danger Zone-Use a walk-behind mower and/or hand
trimmer on slopes greater than 15 degrees

3.

Water

4.

W=width of the machine

5.

Keep a safe distance (twice the width of the machine)
between the machine and any hazard.

•

Avoid starting, stopping or turning the machine on
slopes. Avoid making sudden changes in speed or
direction; turn slowly and gradually.

•

Do Not operate a machine under any conditions
where traction, steering or stability is in question.
Be aware that operating the machine on wet
grass, across slopes or downhill may cause the
machine to lose traction. Loss of traction to the
drive wheels may result in sliding and a loss of
braking and steering. The machine can slide even
if the drive wheels are stopped.

•

Remove or mark obstacles such as ditches, holes,
ruts, bumps, rocks or other hidden hazards. Tall
grass can hide obstacles. Uneven terrain could
overturn the machine.

•

Use extra care while operating with accessories or
attachments, such as grass collection systems.
These can change the stability of the machine
and cause a loss of control. Follow directions for
counter weights.

•

If possible, keep the deck lowered to the ground
while operating on slopes. Raising the deck while
operating on slopes can cause the machine to
become unstable.

Operating the Parking
Brake

Always engage the parking brake when you stop the
machine or leave it unattended.

Engaging the Parking Brake

Park the machine on a level surface.

g188778

Figure 12

Disengaging the Parking Brake

To disengage the parking brake, pull the lever out of
the detent slot and toward you, then push it down
(

Figure 13

).

g188777

Figure 13

1.

Push the parking brake
out of the detent slot and
toward you.

2.

Push the parking brake
down.

18

 

Содержание TimeCutter HD ZX4800

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды