manualshive.com logo in svg

Toro TimeCutter 74750, Руководство оператора

Поделиться
Скачать
Toro TimeCutter 74750 Скачать руководство пользователя страница 34

Charging the Battery

Service Interval:

Before storage—Charge the battery and

disconnect battery cables.

1.

Remove the battery from the chassis; refer to

Removing

the Battery (page 33)

.

2.

Charge the battery for a minimum of 1 hour at 6 to
10 amps.

Note:

Do not overcharge the battery.

3.

When the battery is fully charged, unplug the charger
from the electrical outlet, then disconnect the charger
leads from the battery posts (

Figure 40

).

Figure 40

1.

Positive (+) battery post

3.

Red (+) charger lead

2.

Negative (–) battery post

4.

Black (–) charger lead

Installing the Battery

1.

Position the battery in the tray (

Figure 39

).

2.

Using the fasteners previously removed, install the
positive (red) battery cable to the positive (+) battery
terminal.

3.

Using the fasteners previously removed, install the
negative battery cable to the negative (-) battery
terminal.

4.

Slide the red terminal boot onto the positive (red)
battery post.

5.

Secure the battery with the hold-down (

Figure 39

).

6.

Lower the seat.

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance; however, if a fuse blows, check the
component/circuit for a malfunction or short.

Fuse type:

•

Main—F1-30 A, blade-type

•

Charge Circuit—F2-25 A, blade-type

1.

Remove the screws securing the control panel to the
machine.

Note:

Retain all fasteners.

2.

Lift the control pane up to access the main wire harness
and fuse block (

Figure 41

).

3.

To replace a fuse, pull out on the fuse to remove it
(

Figure 41

).

30

25

30

25

G014921

2

1

Figure 41

1.

Main—30 A

2.

Charge circuit—25 A

4.

Return the control panel to its original position.

Note:

Use the screws removed previously to secure

the panel to the machine.

34

 

Содержание TimeCutter 74750

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды