Toro timecutter 19-52ZX Скачать руководство пользователя страница 2

2

 2003 by The Toro Company

8111 Lyndale Avenue South
Bloomington, MN  55420-1196

Contact us at www.Toro.com

All Rights Reserved

Printed in the USA

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

Warning

Important

 

This engine is not equipped with a spark

arrester muffler. It is a violation of California Public
Resource Code Section 4442 to use or operate this engine
on any forest-covered, brush-covered, or grass-covered
land. Other states or federal areas may have similar laws.

This spark ignition system complies with Canadian
ICES-002.

Ce système d’allumage par étincelle de véhicule est
conforme à la norme NMB-002 du Canada.

The enclosed Engine Owner’s Manual is supplied for
information regarding The U.S. Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance
and warranty.

Keep this engine Owner’s Manual with your unit.
Should this engine Owner’s Manual become damaged
or illegible, replace immediately. Replacements may be
ordered through the engine manufacturer.

Contents

Page

Introduction

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Safety

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Safe Operating Practices

3

. . . . . . . . . . . . . . . . . . . . 

Toro Riding Mower Safety

5

. . . . . . . . . . . . . . . . . . 

Slope Chart

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Safety and Instruction Decals

9

. . . . . . . . . . . . . . . . 

Gasoline and Oil

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Recommended Gasoline

13

. . . . . . . . . . . . . . . . . . . . 

Using Stabilizer/Conditioner

13

. . . . . . . . . . . . . . . . 

Filling the Fuel Tank

13

. . . . . . . . . . . . . . . . . . . . . . 

Checking the Engine Oil Level

13

. . . . . . . . . . . . . . 

Operation

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Think Safety First

14

. . . . . . . . . . . . . . . . . . . . . . . . . 

Controls

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Using the Parking Brake

15

. . . . . . . . . . . . . . . . . . . . 

Starting and Stopping the Engine

15

. . . . . . . . . . . . . 

Operating the Power Take Off (PTO)

16

. . . . . . . . . . 

The Safety Interlock System

16

. . . . . . . . . . . . . . . . 

Page

Testing the Safety Interlock System

16

. . . . . . . . . . . 

Driving Forward or Backward

17

. . . . . . . . . . . . . . . 

Stopping the Machine

17

. . . . . . . . . . . . . . . . . . . . . . 

Adjusting the Height of Cut

17

. . . . . . . . . . . . . . . . . 

Adjusting the Anti-Scalp Rollers

18

. . . . . . . . . . . . . 

Positioning the Seat

18

. . . . . . . . . . . . . . . . . . . . . . . 

Adjusting the Motion Control Levers

19

. . . . . . . . . . 

Pushing the Machine by Hand

19

. . . . . . . . . . . . . . . 

Side Discharge

19

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Tips for Mowing Grass

20

. . . . . . . . . . . . . . . . . . . . . 

Maintenance

21

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Recommended Maintenance Schedule

21

. . . . . . . . . 

Servicing the Engine Oil

22

. . . . . . . . . . . . . . . . . . . 

Cleaning the Cooling System

23

. . . . . . . . . . . . . . . . 

Servicing the Air Cleaner

24

. . . . . . . . . . . . . . . . . . . 

Servicing the Spark Plug

25

. . . . . . . . . . . . . . . . . . . 

Servicing the Battery

25

. . . . . . . . . . . . . . . . . . . . . . 

Servicing the Fuses

28

. . . . . . . . . . . . . . . . . . . . . . . . 

Replacing the Fuel Filter

28

. . . . . . . . . . . . . . . . . . . 

Draining the Fuel Tank

28

. . . . . . . . . . . . . . . . . . . . . 

Greasing and Lubrication

29

. . . . . . . . . . . . . . . . . . . 

Checking the Tire Pressure

29

. . . . . . . . . . . . . . . . . . 

Servicing the Cutting Blades

30

. . . . . . . . . . . . . . . . 

Leveling the Mower from Side-to-Side

31

. . . . . . . . 

Adjusting the Front-to-Rear Blade Slope

32

. . . . . . . 

Inspecting the Belts

33

. . . . . . . . . . . . . . . . . . . . . . . 

Replacing the Mower Belt

34

. . . . . . . . . . . . . . . . . . 

Removing the Mower

35

. . . . . . . . . . . . . . . . . . . . . . 

Installing the Mower

35

. . . . . . . . . . . . . . . . . . . . . . 

Washing the Underside of the Mower

35

. . . . . . . . . 

Replacing the Grass Deflector

36

. . . . . . . . . . . . . . . 

Wiring Diagram

37

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Cleaning and Storage

38

. . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

39

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

The Toro Total Coverage Guarantee

44

. . . . . . . . . . . . . 

Introduction

Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe
products, you are responsible for operating the product
properly and safely.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 illustrates
the location of the model and serial numbers on the
product.

Содержание timecutter 19-52ZX













































Отзывы: