background image

13

Operation

Note: Determine the left and right sides of the machine
from the normal operating position.

Think Safety First

Please carefully read all of the safety instructions and
decals in the safety section. Knowing this information
could help you, your family, pets or bystanders avoid
injury.

Danger

Mowing on wet grass or steep slopes can cause
sliding and loss of control.

Wheels dropping over edges can cause rollovers,
which may result in serious injury, death or
drowning.

To avoid loss of control and possibility of rollover:

Do not mow near drop–offs or near water.

Do not mow slopes greater than 15 degrees.

Reduce speed and use extreme caution on slopes.

Avoid sudden turns or rapid speed changes.

2

3

1

m–6491

Figure 2

1.

Safe Zone—use the
Timecutter here

2.

Use walk behind mower
and/or hand trimmer near
drop–offs and water.

3.

Water

Controls

Become familiar with all of the controls (Fig. 3 and 4)
before you start the engine and operate the machine.

m–5135

1

2

3

4

Figure 3

1.

Ignition switch

2.

Throttle/Choke

3.

Power take off (PTO)

4.

Headlights—optional

m–5134

1

1

2

3

Figure 4

1.

Motion control lever

2.

Parking brake lever

3.

Height-of-cut lever

Содержание TimeCutter 17-52ZX









































Отзывы: