manualshive.com logo in svg

Toro Reelmaster 5510 Series, Руководство по обслуживанию


Поделиться
Скачать
background image

CAN-bus Terminator Resistor

g223018

Figure 279

1.

CAN-bus terminator resistor

2.

Keyway

The system communication between the electrical components on the
Reelmaster machine is accomplished on a CAN-bus communication system.
The 2 specially designed, twisted cables form the bus for the network are used
on the machine. These wires provide the data pathways between the machine
components.

The 120 ohm CAN-bus terminator resistor plugs into the main wire harness in the
control arm. The resistor can be accessed by removing the left control arm cover.

On machines with a Kubota diesel engine, the second CAN-bus terminator
resistor plugs into the engine wire harness near the engine starter motor. The
engine wire harness connector has a blue insert to identify the proper location for
the terminator resistor.

On machines with a Yanmar diesel engine or Kubota gasoline engine, the
second CAN-bus terminator resistor is included in the engine ECU. This resistor
cannot be accessed for testing.

Note:

The insulator wedge in the terminator resistor is blue for identification

purposes. There is also a center keyway to prevent the terminator resistor from
plugging into the wrong wire harness connector.

Note:

Refer to the Electrical Schematic and Wire Harness Drawings/Diagrams

for additional information on the location of the terminator resistor and wire
connections.

IMPORTANT

The terminator resistor is required for proper electrical system
operation.

Testing the CAN-bus Terminator Resistor

1. The CAN-bus terminator resistor (

Figure 279

) can be tested using a digital

multimeter (ohms setting). Locate the CAN-bus terminator resistor and
remove the cable tie that secures the resistor to the wire harness. Unplug the
resistor from the wire harness for testing.

2. Use a digital multimeter (ohms setting) to measure the resistance value for

the CAN-bus terminator resistor. There should be

120 ohms

resistance

between the terminals A and B. The terminal C is not used.

3. If the testing determines that the CAN-bus terminator resistor is damaged,

replace the CAN-bus terminator resistor.

Electrical System: Testing the Electrical Components

Page 7–114

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

FENDT 4300 Workshop Service Manual preview
4300
Бренд: FENDT Страницы: 31
B&K 4416 Service Manual preview
4416
Бренд: B&K Страницы: 16
B.A. International BA Ultimate LED Operating Instructions Manual preview
BA Ultimate LED
Бренд: B.A. International Страницы: 234
Raymarine ST60+ SPEED INSTRUMENT Owner'S Handbook Manual preview
ST60+ SPEED INSTRUMENT
Бренд: Raymarine Страницы: 60
Raymarine Maxiview ST80 Operation Manual preview
Maxiview ST80
Бренд: Raymarine Страницы: 15
Raven SmarTrax Calibration & Operation Manual preview
SmarTrax
Бренд: Raven Страницы: 58
Raven Sidekick Pro Quick Installation Reference preview
Sidekick Pro
Бренд: Raven Страницы: 26
Alcoscan AL4000 User Manual preview
AL4000
Бренд: Alcoscan Страницы: 6
ProLights HZ900D User Manual preview
HZ900D
Бренд: ProLights Страницы: 28
Harken MKIII UNIT 3 Instruction Manual preview
MKIII UNIT 3
Бренд: Harken Страницы: 78
Sulky Xeos TF Original Instructions Manual preview
Xeos TF
Бренд: Sulky Страницы: 99
EuroLite AKKU BEK-10 Kaleidoscope User Manual preview
AKKU BEK-10 Kaleidoscope
Бренд: EuroLite Страницы: 16
Cardinal Health CAX1230FA Installation & Operation Manual preview
CAX1230FA
Бренд: Cardinal Health Страницы: 36
Martin Destroyer X250 User Manual preview
Destroyer X250
Бренд: Martin Страницы: 16
Ibiza LAS360RG-FIREFLY User Manual preview
LAS360RG-FIREFLY
Бренд: Ibiza Страницы: 15
Land Pride SGC0660 Operator'S Manual preview
SGC0660
Бренд: Land Pride Страницы: 30
AVE LEDBAR-24 User Manual preview
LEDBAR-24
Бренд: AVE Страницы: 8
VAREM AQUAFILL HP Instruction Manual preview
AQUAFILL HP
Бренд: VAREM Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды