manualshive.com logo in svg

Toro Reelmaster 5510 Series, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine Relays with 5 Terminals (Gasoline Engine)

g228830

Figure 260

1.

Engine power center

3.

Power relay

2.

Start relay

4.

Fuel pump relay

The engine electrical system in machines with a Kubota gasoline engine includes
3 electrical relays that have 5 terminals. These relays are installed in the engine
power center located on the engine (

Figure 260

).

The start relay is used to provide current to the engine starter solenoid. The start
relay is energized by the engine ECU.

The power relay is used to provide electrical power to several engine electrical
components when energized by the engine ECU.

The fuel pump relay is used to provide electrical power to the fuel pump when
energized by the engine ECU.

Note:

An engine fault code may be displayed on the InfoCenter Display if the

power relay, fuel pump relay or circuit wiring is damaged.

Testing the Engine Relays with 5 Terminals

1. Park machine on a level surface, lower cutting units, shut off the engine,

apply parking brake and remove key from key switch.

2. Raise and support hood to access engine relays. Remove engine power

center cover and locate relay(s) to be tested. Remove relay from the engine
power center for testing.

Note:

Prior to taking small resistance readings with a digital multimeter, short

the meter test leads together. The meter will display a small resistance value
(usually 0.5 ohms or less). This resistance is due to the internal resistance
of the meter and test leads. Subtract this value from the measured value
of the component you are testing.

Electrical System: Testing the Electrical Components

Page 7–92

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

JB-Lighting A8 Upgrade Manual preview
A8
Бренд: JB-Lighting Страницы: 40
Hagie 204 Operator'S Manual preview
204
Бренд: Hagie Страницы: 141
Fellowes SafeCut Atom User Manual preview
SafeCut Atom
Бренд: Fellowes Страницы: 20
DOTLUX FLOOReco 5164-040120 User Manual preview
FLOOReco 5164-040120
Бренд: DOTLUX Страницы: 10
Land Pride Retractable Box Scrapers HR3584 Specifications preview
Retractable Box Scrapers HR3584
Бренд: Land Pride Страницы: 1
Heiniger EVO/H Translation Of The Original Instructions preview
EVO/H
Бренд: Heiniger Страницы: 164
Fast MT765 Challenger Installation-Parts preview
MT765 Challenger
Бренд: Fast Страницы: 31
B&G RAM T0 User Manual preview
RAM T0
Бренд: B&G Страницы: 16
Milestone BoneSTATION Operator'S Manual preview
BoneSTATION
Бренд: Milestone Страницы: 64
Nano Temper Monolith NT.115 User Manual preview
Monolith NT.115
Бренд: Nano Temper Страницы: 24
Parkside PALA 2000 A1 Operation And Safety Notes preview
PALA 2000 A1
Бренд: Parkside Страницы: 88
Hantek DSO8000E Series User Manual preview
DSO8000E Series
Бренд: Hantek Страницы: 95
Ikan RS-F100 Quick Start Manual And Important Safeguards preview
RS-F100
Бренд: Ikan Страницы: 5
Toparc MATCHPEN Manual preview
MATCHPEN
Бренд: Toparc Страницы: 32
ASIA TECHNOLOGY AF-300 Operating Manual & Parts List preview
AF-300
Бренд: ASIA TECHNOLOGY Страницы: 38
Ivoclar Vivadent Ivomat IP3 Operating Instructions Manual preview
Ivomat IP3
Бренд: Ivoclar Vivadent Страницы: 64
OttLite 580083 Quick Start Manual preview
580083
Бренд: OttLite Страницы: 5
Barnstead LAB-LINE MAX Q 4000 Operation Manual preview
LAB-LINE MAX Q 4000
Бренд: Barnstead Страницы: 35

Бренды по названию

Популярные бренды

Загрузить еще бренды