manualshive.com logo in svg

Toro Reelmaster 5510 Series, Руководство по обслуживанию


Поделиться
Скачать
background image

DANGER

Because gasoline is highly flammable, use caution when storing or
handling it. Do not smoke while filling the fuel tank. Do not fill fuel
tank while engine is running, when engine is hot or when machine
is in an enclosed area. Always fill fuel tank outside and wipe up
any spilled fuel before starting the engine. Store fuel in a clean,
safety-approved container and keep container cap in place. Use
gasoline for the engine only; not for any other purpose.

Checking the Fuel Lines and Connections

Check fuel lines and connections periodically as recommended in the

Traction

Unit Operator’s Manual

. Check lines for deterioration, damage, leakage or loose

connections. Replace fuel hoses, clamps and connections as necessary.

Drain and Clean Fuel Tank

Drain and clean the fuel tank periodically as recommended in the

Traction

Unit Operator’s Manual

. Also, drain and clean the fuel tank if the fuel system

becomes contaminated or if the machine is to be stored for an extended period.

IMPORTANT

Follow all local codes and regulations when recycling or disposing
waste fuel.

To clean fuel tank, flush tank out with clean solvent. Ensure that the tank is
free of all contaminates and debris.

Priming the Fuel System

The fuel system needs to be primed before starting the engine for the first time,
after running out of fuel or after fuel system maintenance (e.g., replacing a fuel
hose, cleaning the fuel tank). To prime the fuel system, ensure that the fuel tank
has fuel in it. Then, turn the key switch to the R

UN

position for 10 to 15 seconds

which allows the fuel pump to prime the fuel system. Do not use the engine
starter motor to crank the engine in order to prime the fuel system.

Removing the Fuel Tank

1. Park machine on a level surface, lower cutting units, stop engine, engage

parking brake and remove key from the key switch.

2. Place drain pan under fuel tank. Ensure that drain pan is large enough to

hold fuel tank contents; refer to

Specifications (page 3–2)

.

3. Open draincock on bottom of fuel tank and allow tank to fully drain. Close

draincock.

IMPORTANT

To prevent damage to fuel hoses, numerous cable ties are used to
secure hoses to machine components. Take note of all cable ties
that are removed from machine during fuel tank removal so they can
be properly replaced during tank installation.

Kubota Gasoline Engine: Service and Repairs

Page 5–12

Reelmaster

®

5410/5510/5610 Series

15216SL Rev C

Содержание Reelmaster 5510 Series























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Reelmaster 5510 Series

Hagie 2101 Operator'S Manual Supplement preview
2101
Бренд: Hagie Страницы: 61
Raytheon V700 Instruction Manual preview
V700
Бренд: Raytheon Страницы: 69
QBC Diagnostics Star Operators & Service Manual preview
Star
Бренд: QBC Diagnostics Страницы: 65
IBEX TS100 Quick Start Manual preview
TS100
Бренд: IBEX Страницы: 10
Garmin GSD20 Sounder Installation Manual preview
GSD20 Sounder
Бренд: Garmin Страницы: 12
Garmin GC 12 Installation Instructions Manual preview
GC 12
Бренд: Garmin Страницы: 13
Hantek DPO6000 Series Product Manual preview
DPO6000 Series
Бренд: Hantek Страницы: 124
Vari Lite BeamLine VL800 User Manual preview
BeamLine VL800
Бренд: Vari Lite Страницы: 14
Vaniman VANGUARD 1X Quick Start Manual preview
VANGUARD 1X
Бренд: Vaniman Страницы: 3
Mako MK5 Operator'S Manual preview
MK5
Бренд: Mako Страницы: 17
BARRON Exitronix LEMD Series Installation Instructions Manual preview
Exitronix LEMD Series
Бренд: BARRON Страницы: 6
velda T-Flow Tronic Series User Instructions preview
T-Flow Tronic Series
Бренд: velda Страницы: 8
CEM Discover Protein Hydrolysis Installation And Operation Instructions Manual preview
Discover Protein Hydrolysis
Бренд: CEM Страницы: 6
Pulse LOGO30 Manual preview
LOGO30
Бренд: Pulse Страницы: 4
Expolite PROFILLED 750 User Manual preview
PROFILLED 750
Бренд: Expolite Страницы: 20
Hobby Components V2 4x4x4 LED Cube Kit Build Manual preview
V2 4x4x4 LED Cube Kit
Бренд: Hobby Components Страницы: 24
Feniex FUSION GPL FN-0120 Instruction Manual preview
FUSION GPL FN-0120
Бренд: Feniex Страницы: 5
Spector&Co SpecTech T1043 User Manual preview
SpecTech T1043
Бренд: Spector&Co Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды