background image

California Emission Control Warranty
Statement

Your Warranty Rights And Obligations

The California Air Resources Board and Toro are pleased to explain the emission control system
warranty of your 1995 and later lawn and garden equipment engine. In California, new lawn and garden
equipment engines must be designed, built and equipped to meet the State’s stringent anti–smog
standards. Toro must warrant the emission control system on your lawn and garden equipment engine for
the periods of time listed below provided there has been no abuse, neglect or improper maintenance of
your lawn and garden equipment engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, and catalytic converter. Also included may be hoses, belts, connectors and other
emission–related assemblies.

Where a warrantable condition exists, Toro will repair your lawn and garden equipment engine at no cost
to you including diagnosis, parts and labor.

The 1995 and later utility and lawn and garden equipment engines are warranted for two years. If any
emission–related part on your engine is defective, the part will be repaired or replaced by Toro.

Owner’s Warranty Responsibilities:

As the lawn and garden equipment engine owner, you are responsible for the performance of the
required maintenance listed in your Operator’s manual
. Toro recommends that you retain all
receipts covering maintenance on your lawn and garden equipment engine, but Toro cannot deny
warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled
maintenance.

As the lawn and garden equipment engine owner, you should however be aware that Toro may deny
you warranty coverage if your lawn and garden equipment engine or a part has failed due to abuse,
neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your lawn and garden equipment engine to a Toro Authorized
Service Dealer as soon as a problem exists. The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call
1–800–237–2654.

Содержание ProLine 53030

































Отзывы: