Toro ProLine 20 HP Скачать руководство пользователя страница 48

What Is Covered By This Express Warranty?

The Toro Company promises to repair any TORO Product
used for commercial, institutional, or rental purposes if defec-
tive in materials or workmanship. The following time frames
apply from the date of purchase:
Product

Warranty Period

All Products

1 year

. . . . . . . . . . . . . . . . . . 

All Spindles

2 years parts & labor, 

. . . . . . . . . . . . . . . . . . . 

3rd year parts only

Engines on the following:

2 years

. . . . . . . . . 

Out Front and MidMount Zero Radius Tractors
ProLine Mid–size Mowers
Groundsmaster Riding Mowers
ProLine Hand Held Gas Products
(AE & LE engines only)
Backpack Blowers

The cost of parts and labor are included, but the customer
pays the transportation cost. Transportation within a 15–mile
radius of a TORO ProLine Service Dealer is covered under
this warranty for Riding Products, Midsize Mowers and Turf
Maintenance Equipment.

What Products Are Covered By This Warranty?

Z-Master Zero Radius Tractors

ProLine Mid-size Mowers

Groundsmaster Riding Mowers

ProLine Hand-held Gas Products

Backpack Blowers

Turf Maintenance Equipment

Debris Management Equipment

How About Residential Use?

TORO Products used for residential use are covered by a full
two-year warranty.

How Do You Get Warranty Service?

Should you feel your TORO Product contains a defect in ma-
terials or workmanship, contact the dealer who sold you the
product or any TORO ProLine Service Dealer. The Yellow
Pages of your telephone directory is a good reference
source; look under TORO Commercial Service Dealers. The
Service Dealer will either arrange service at his/her dealer-
ship or recommend another authorized Service Dealer who
may be more convenient. You may need proof of purchase
(copy of registration card, sales receipt, etc.) for warranty
validation.

       

   +#  %  ## %*

  (!+#  &  ## %*  !#  $ %  $

If for any reason you are dissatisfied with a Service Dealer’s
analysis of the defect in materials or workmanship or if you need
a referral to a TORO ProLine Service Dealer, please feel free to
contact us at the following address:

Toro Customer Service Department

8111 Lyndale Avenue South

Bloomington, MN 55420–1196

612–888–8801 or 800–348–2424

What Must You Do To Keep The Warranty In Effect?

You must maintain your TORO Product by following the main-
tenance procedures described in the operator’s manual. Such
routine maintenance, whether performed by a dealer or by
you, is at your expense.

What Does This Warranty Not Cover?

and

How Does Your State Law Relate To This Warranty?

There is no other express warranty except for special emis-
sion system coverage on some products and as described
above. This express warranty does not cover:

Cost of regular maintenance service or parts, such as
filters, fuel, lubricants, tune-up parts, blade sharpening,
brake and clutch adjustments.

Any product or part which has been altered or misused or
required replacement or repair due to normal wear, acci-
dents, or lack of proper maintenance.

Repairs necessary due to improper fuel, contaminants in
the fuel system, or failure to properly prepare the fuel sys-
tem prior to any period of non-use over three months.

Pickup and delivery charges for distances beyond a
15-mile radius from a TORO ProLine Service Dealer.

All repairs covered by this warranty must be performed by a
TORO Service Dealer using Toro approved replacement parts.

The Toro Company is not liable for indirect or consequen-
tial damages in connection with the use of the TORO
Products covered by this warranty, including any cost or
expense of providing substitute equipment or service dur-
ing reasonable periods of malfunction or non-use pend-
ing completion of repairs under this warranty. Some
states do not allow exclusions of incidental or conse-
quential damages, so the above exclusion may not apply
to you.

This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

              

&$%!#$ (!  '  "&#$    "#!&%$  )"!#%  #!  %   %  %%$  !#     $!&  ! %%  %#     $+

%#&%!#   #  %!  !%   &# %  "!$  !#  *!&#  !& %#*  "#!'   !#  $%%    !#   *  #$!   *!&  #  $$%$  (%

*!&#   $%#&%!#$  $#'  !#  '  &%*  !%    &# %   !#%!   ! %%  %    "!#%#      !%#  #$

  *!&  *  ! %%  &$  %    !#!  !" *

Rev  9/30/98

Содержание ProLine 20 HP

















































Отзывы: