manualshive.com logo in svg

Toro Power-Max 828LXE, Руководство оператора, Страница: 22 / 24

Поделиться
Скачать
Toro Power-Max 828LXE Скачать руководство пользователя страница 22

22

3352-467

Troubleshooting

Toro designed and built your snowthrower for trouble-free operation. Check the following components and items
carefully, and refer to Maintenance on page 15 for more information. If a problem continues, see an Authorized
Service Dealer.

Problem

Possible Causes

Corrective Action

Electric starter does not turn
(electric-start models only)

1. The power cord is

disconnected at the outlet or
the snowthrower.

1. Connect the power cord to the

outlet and/or the snowthrower.

2. The power cord is worn,

corroded, or damaged.

2. Replace the power cord.

3. The power outlet is not

energized.

3. Have a qualified electrician

energize the power outlet.

Engine does not start or starts

1. The key is not in the ignition or

1. Insert the key into the ignition

Engine does not start or starts
hard

1. The key is not in the ignition or

is in the Stop position.

1. Insert the key into the ignition

and turn it to the On position.

2. The choke is in the Off position

and the primer has not been
pressed.

2. Move the choke to the On

position and press the primer
3 times.

3. The fuel shutoff valve is not

open.

3. Open the fuel shutoff valve.

4. The throttle is not in the Fast

position.

4. Move the throttle to the Fast

position.

5. The fuel tank is empty or the

fuel system contains stale fuel.

5. Drain and/or fill the fuel tank

with fresh gasoline (not more
than 30 days old). If the
problem persists, contact your
Authorized Service Dealer.

6. The spark plug wire is loose or

disconnected.

6. Connect the wire to the spark

plug.

7. The spark plug is pitted, fouled,

or the gap is incorrect.

7. Check the spark plug and

adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.

8. The fuel cap vent is restricted.

8. Remove the vent restriction or

replace the fuel cap.

9. The engine oil level in the

engine crankcase is too low or

9. Add or drain oil to adjust the oil

level in engine crankcase to the

engine crankcase is too low or
too high.

level in engine crankcase to the
Full mark on the dipstick.

Engine runs rough

1. The choke is in the On position.

1. Move the choke to the Off

position.

2. The fuel shutoff valve is not

completely open.

2. Open the fuel shutoff valve.

3. The fuel tank is nearly empty or

contains stale fuel.

3. Drain and fill the fuel tank with

fresh gasoline (not more than
30 days old). If the problem
persists, contact an Authorized
Service Dealer.

4. The spark plug wire is loose.

4. Connect the wire to the spark

plug.

Содержание Power-Max 828LXE

























Отзывы:

Нет отзывов