Toro Multi Pro 41394 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 96

background image

3.

Check the condition of all spray hoses.

Note:

Replace any hoses that are worn or

damaged.

4.

Tighten all hose clamps and fittings.

Servicing the Engine

1.

Service the air cleaner; refer to

Air Cleaner (page 55)

.

2.

Change the engine-oil filter and oil; refer to

Changing the Engine Oil Filter (page 57)

and

Changing the Engine Oil (page 58)

.

Servicing the Fuel System

1.

Drain the fuel tank; refer to

Draining the Fuel

Tank (page 62)

.

2.

Prepare fuel with fuel stabilizer according to the
manufacturer’s instructions, and add it to the
fuel tank.

3.

Start the engine and run it at idle speed for 5
minutes.

4.

Shut off the engine.

5.

Secure all the fuel-system fittings.

Servicing the Battery

1.

Move the machine in a clean, dry storage area.

2.

Remove the battery from the chassis; refer to

Removing the Battery (page 63)

.

Note:

Do not connect the battery cables to the

battery posts during storage.

3.

Check the electrolyte level.

4.

Fully charge the battery; refer to

Battery (page 64)

.

Important:

The battery must be fully

charged to prevent it from freezing and being
damaged at temperatures below 32°F (0°C).
A fully charged battery maintains its charge
for about 50 days at temperatures lower
than 4°C (40°F). If the temperatures will be
above 4°C (40°F), check the water level in the
battery and charge it every 30 days.

Protecting the Machine

1.

Remove the key from the starter switch and
put the key in a safe place out of the reach of
children.

2.

Cover the machine to protect it and keep it clean.

Preparing the Machine for
Service

1.

Insert the pressure-gauge tube into the tube
coupler at back of the pressure gauge (

g276304

Figure 125

1.

Pressure-gauge tube

3.

Pressure gauge

2.

Tube coupler

2.

Close the spigot of the fresh-water tank.

3.

Add fuel to the fuel tank.

4.

Fully charge the battery; refer to

Battery (page 64)

.

5.

Install the battery into the chassis; refer to

Installing the Battery (page 64)

.

88

«
...
86
87
88
89
90
...
»

Содержание Multi Pro 41394

































































































Отзывы:

Нет отзывов

Похожие инструкции для Multi Pro 41394

Бренд: Zenoah Страницы: 16

Бренд: Dramm Страницы: 25

Бренд: Tarmo Страницы: 7

Бренд: Rockwell Страницы: 12

TurboPro CL100ESH

Бренд: CLOROX Страницы: 10

Total 360 CLX1100

Бренд: CLOROX Страницы: 17

Бренд: Sanique Страницы: 20

Бренд: MSW Motor Technics Страницы: 11

Бренд: Graco Страницы: 8

Бренд: P.Lindberg Страницы: 147

HEAVYCOAT HC730 GAS

Бренд: WAGNER Страницы: 148

Бренд: Eastwood Страницы: 12

Бренд: WAGNER Страницы: 46

Бренд: Agri-Fab Страницы: 2

SATAminijet 3 HVLP

Бренд: SATA Страницы: 6

Бренд: Retsch Страницы: 64

Бренд: Mastergrip Страницы: 12

Бренд: Mastergrip Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды