Toro GreensPro 1240 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 186

background image

General Information

The GreensPro

Operator's Manual

provides information regarding the operation,

general maintenance procedures, and maintenance intervals for your machine.
Refer to the GreensPro

Operator's Manual

for additional information when

servicing the machine.

Some service and repair parts for the transmission in your GreensPro 1240
machine and for the hydraulic pump in your GreensPro 1260 machine are
supplied through your Authorized Toro Distributor. Be prepared to provide your
distributor with the Toro Model and Serial Number of your machine to obtain parts.

Transmission/Hydraulic Pump Service and Repair Manuals

Detailed information on troubleshooting, testing, disassembly, and assembly is
provided in the Hydro-Gear Model BDR Service and Repair Manual (GreensPro
1240) and the Hydro-Gear P Series Hydrostatic Pump Service and Repair
Manual (GreensPro 1260). The use of some specialized tools and test
equipment is explained in the Hydro-Gear Service and Repair Manual. However,
the specialized nature of some transmission repairs may dictate that the work be
done at an Authorized Hydro-Gear Service Dealer.

Hydraulic System: General Information

Page 5–2

GreensPro

™

1240/1260

14211SL Rev A

«
...
46
47
48
49
50
...
»

Содержание GreensPro 1240



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GreensPro 1240

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: Paitec Страницы: 14

Бренд: Earmor Страницы: 5

Бренд: Bang & Olufsen Страницы: 2

Бренд: Barreto Страницы: 20

Бренд: Backyard Discovery Страницы: 41

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Quark-Elec Страницы: 2

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: iBACheck Страницы: 2

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренд: Rapid Shape Страницы: 12

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды