Toro GreensPro 1240 Скачать руководство пользователя страница 101

Страница: 101 / 186

Hydraulic Motor (GreensPro 1260)

g240365

Figure 40

GreensPro 1260

Socket-head screw

Bearing housing

17.

Bolt (4 each)

Spring washer

10.

Locknut (4 each)

18.

Drive roller hub

Plain washer (5 each)

11.

Plain washer (8 each)

19.

Drive roller

Hardened washer

12.

Bolt (4 each)

20.

Bearing

Brake hub

13.

Carriage screw (2 each)

21.

Shim (as required)

Bolt (2 each)

14.

Wheel motor nut

22.

Nut (4 each)

Plain washer (6 each)

15.

Woodruff key

23.

Motor guard

Spacer (2 each)

16.

Hydraulic motor

The hydraulic motor and drive roller should be removed from machine as
an assembly. Once removed from the machine, the hydraulic motor can be
separated for service.

Removing the Hydraulic Motor and Drive Roller Assembly

Refer to

Figure 40

for this procedure.

GreensPro

™

1240/1260

Page 5–55

Hydraulic System: Service and Repairs

14211SL Rev A

Содержание GreensPro 1240



























































































































































































Результаты поиска

Содержание GreensPro 1240

Отзывы:

Похожие инструкции для GreensPro 1240

Бренды по названию

Популярные бренды

Toro GreensPro 1240, Руководство по обслуживанию

Результаты поиска

Содержание GreensPro 1240

Отзывы:

Похожие инструкции для GreensPro 1240

Бренды по названию

Популярные бренды