Toro Greensmaster 3120 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 48

Toro Greensmaster 3120 Скачать руководство пользователя страница 35

Adjusting the Transport
Speed

Obtaining the Maximum Transport
Speed

The traction pedal comes adjusted for
maximum-transport speed, but you may need
to adjust it if the pedal reaches full stroke before it
contacts the pedal stop, or if you want to a decrease
the transport speed.

To obtain the maximum-transport speed, put the
functional control lever in the T

RANSPORT

position and

press down on the traction pedal. If the pedal contacts
the stop (

) before you feel tension on the

cable, perform the following adjustment procedure:

g005520

Figure 44

1.

Pedal stop

1.

Put the functional-control lever in the T

RANSPORT

position and loosen the locknut securing the
pedal stop to the floor plate (

2.

Tighten the pedal stop until it does not contact
the traction pedal.

3.

Continue applying a light load on the transport
pedal and adjust the pedal stop so it contacts
the pedal rod and tighten the nuts.

Important:

Ensure that the tension on the

cable is not excessive or you will reduce the
cable life.

Reducing the Transport Speed

1.

Press down on the traction pedal and loosen the
locknut securing the pedal stop to the floor plate.

2.

Loosen the pedal stop until you obtain the
desired transport speed.

3.

Tighten the locknut securing the pedal stop.

Adjusting the Mowing
Speed

Factory setting: 6.1 km/h (3.8 mph)

1.

Loosen the jam nut on the trunnion bolt on the
side of the traction pedal (

).

g032584

Figure 45

1.

Trunnion bolt

2.

Jam nut

2.

Rotate the trunnion bolt counterclockwise to
increase the mowing speed and clockwise to
decrease it.

3.

Tighten the jam nut without turning the trunnion
bolt and check the ground speed. Repeat this
procedure, if required.

35

«
...
33
34
35
36
37
...
»

Содержание Greensmaster 3120

















































Отзывы:

Нет отзывов