Toro Greensmaster 1018 Скачать руководство пользователя страница 176

Страница: 176 / 179

The Height Adjuster Assembly

g282214

Figure 91

Cotter pin

Compression spring

13.

Quick up cover

Clevis pin

Bumper

14.

Detent spring

Height adjustment rod

Lock nut

15.

Button-head screw

Flange nut

10.

Pinch bolt

16.

Height adjuster knob

Washer (2 each)

11.

Height-of-cut bracket

17.

Height adjustment bolt

Compression spring

12.

Quick up lever

18.

Plow bolt

Note:

Early universal groomers used 2 compression springs on non-adjustable

height adjustment rods. Retrofitting the assemblies on each side of the cutting
unit with new compression springs, height adjustment rods, and adding flange
nuts to enable spring adjustment is recommended; refer to

Figure 91

Disassembling the Height Adjuster

Note:

Refer to

Figure 91

during this procedure.

1. Remove the cutting unit from the machine.

2. Remove the cotter pins and clevis pins that secure the height adjustment

rods to the groomer gear box and idler arm. Discard the cotter pins.

3. Loosen the pinch bolts that secure the front roller to the height-of-cut

brackets.

Universal Groomer (Optional): Service and Repairs

Page 9–14

Greensmaster

1018/1021/1026

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Бренды по названию

Популярные бренды