Toro Greensmaster 1018 страница 171 Скачать руководство пользователя

Страница: 171 / 179

The Idler Assembly

g282209

Figure 88

Cotter pin

Shield

Flange nut

Retaining ring

Flocked seal (2 each)

Bearing

Bushing

Idler arm

Stub shaft

10.

Clevis pin

The groomer idler assembly is located on the opposite side of the groomer gear
box.

Removing the Idler Assembly

Note:

Refer to

Figure 88

during this procedure.

1. Remove the reel drive from the cutting unit; refer to

Removing the Reel

Assembly (page 8–18)

2. Remove the groomer reel assembly; refer to

Removing the Groomer Reel

(page 9–11)

3. Remove the cotter pin and clevis pin from the height adjustment rod at the

front of the idler arm. Discard the cotter pin.

4. Remove the flange nut that secures the idler arm to the stub shaft. Remove

the idler assembly.

5. Inspect the shields, bearing, and bushing in the idler assembly. Replace any

components that are worn or damaged.

Greensmaster

1018/1021/1026

Page 9–9

Universal Groomer (Optional): Service and Repairs

18238SL Rev B

Содержание Greensmaster 1018




















































































































































































Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды

Toro Greensmaster 1018, Руководство по обслуживанию

Результаты поиска

Содержание Greensmaster 1018

Отзывы:

Похожие инструкции для Greensmaster 1018

Бренды по названию

Популярные бренды