Toro GrandStand 74558 Скачать руководство пользователя страница 13

Operation

Adding Fuel

Use

Unleaded

Regular Gasoline suitable for

automotive use (85 pump octane minimum). Leaded
regular gasoline may be used if unleaded regular is not
available.

Important:

Never use methanol, gasoline

containing methanol, or gasohol containing more
than 10% ethanol because the fuel system could be
damaged. Do not mix oil with gasoline.

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and
others and can damage property.

Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any
gasoline that spills.

Never fill the fuel tank inside an enclosed
trailer.

Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1
inch (25 mm) below the bottom of the filler
neck. This empty space in the tank allows
gasoline to expand.

Never smoke when handling gasoline, and
stay away from an open flame or where
gasoline fumes may be ignited by a spark.

Store gasoline in an approved container and
keep it out of the reach of children. Never
buy more than a 30-day supply of gasoline.

Do not operate without entire exhaust
system in place and in proper working
condition.

In certain conditions during fueling, static
electricity can be released causing a spark
which can ignite the gasoline vapors. A fire
or explosion from gasoline can burn you and
others and can damage property.

Always place gasoline containers on the
ground away from your vehicle before filling.

Do not fill gasoline containers inside a
vehicle or on a truck or trailer bed because
interior carpets or plastic truck bed liners
may insulate the container and slow the loss
of any static charge.

When practical, remove gas-powered
equipment from the truck or trailer and
refuel the equipment with its wheels on the
ground.

If this is not possible, then refuel such
equipment on a truck or trailer from a
portable container, rather than from a
gasoline dispenser nozzle.

If a gasoline dispenser nozzle must be used,
keep the nozzle in contact with the rim of
the fuel tank or container opening at all
times until fueling is complete.

Gasoline is harmful or fatal if swallowed.
Long-term exposure to vapors can cause serious
injury and illness.

Avoid prolonged breathing of vapors.

Keep face away from nozzle and gas tank or
conditioner opening.

Keep gas away from eyes and skin.

Using Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to
provide the following benefits:

Keeps gasoline fresh during storage of 90 days or
less. For longer storage it is recommended that the
fuel tank be drained.

Cleans the engine while it runs

Eliminates gum-like varnish buildup in the fuel
system, which causes hard starting

13

Содержание GrandStand 74558

































































Отзывы: