background image

3

3329-471

Do not change the governor settings on the
engine.

When storing the snowthrower for more than 30
days, drain the fuel from the fuel tank to prevent a
potential hazard. Store fuel in an approved fuel
container. Remove the key from the ignition
switch before storing the snowthrower.

Purchase only genuine Toro replacement parts
and accessories.

Sound Pressure

This unit has a maximum sound pressure level at the
operator’s ear of 91 dBA, based on measurements of
identical machines per Directive 98/37/EC.

Sound Power

This unit has a guaranteed sound power level of
108 dBA, based on measurements of identical
machines per Directive 2000/14/EC.

Vibration

This unit does not exceed a hand/arm vibration level
of 15.5 m/s

2

, based on measurements of identical

machines per Directive 98/37/EC.

Safety/Instruction Decals

Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals.

60-9480

94-2561

1.

Hot surface/burn hazard—keep bystanders a safe distance from
the machine.

94-2577

1.

To engage the auger, hold the control bar against the handle.

2.

To disengage the auger, release the control bar.

94-2901

1.

Cutting/dismemberment hazard, impeller and auger—stay away
from moving parts; remove the ignition key and read the
instructions before servicing or performing maintenance.

Содержание CCR 3650 GTS













Отзывы: