manualshive.com logo in svg

Toro 78534, Руководство оператора

Поделиться
Скачать
Toro 78534 Скачать руководство пользователя страница 6

1

Preparing the Machine

No Parts Required

Procedure

1.

Disengage the PTO, move the motion control levers
to the N

EUTRAL

-L

OCKED

position and set the parking

brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Repair all bent or damaged areas of mower deck and
replace any missing parts.

4.

Clean the machine of any debris on the deck or rear
part of the machine to ease installation.

2

Installing the Bagger Mounting
Bracket

Parts needed for this procedure:

1

Bagger mounting bracket

2

Bagger side plate

2

Spacer

14

Bolt (3/8 x 1-1/2 inches)

2

Bolt (3/8 x 1 inch) (for Z593 machines only)

14

Flange Nut (3/8 inch)

14

Curved washer

Procedure

Important:

Do not tighten any bolts until both side

brackets and bagger mounting bracket are fit loose on
the machine.
Refer to

3 Tightening all Mounting Bolts (page 8)

for the

correct procedure to tighten the bolts.

1.

Remove the bolts, nuts, and washers holding the roll
bar to one side of the machine. Discard the nuts, bolts,
and washers (

Figure 4

,

Figure 5

, and

Figure 6

).

2.

Install the bagger side plate and the roll bar section
to the side of the machine using 4 bolts (3/8 x 1-1/2
inches), 4 curved washers (3/8 inch), and 4 flange nuts
(3/8 inch) as shown in

Figure 4

,

Figure 5

, and

Figure 6

.

3.

Repeat the steps above for the opposite side (

Figure

4

,

Figure 5

, and

Figure 6

).

Note:

Make sure the curved washers are installed as

shown in

Figure 4

,

Figure 5

, and

Figure 6

.

4.

Install the bagger mounting bracket to the left and right
side bagger brackets with 4 bolts (3/8 x 1-1/2 inches),
4 curved washers (3/8 inch), and 4 flange nuts (3/8
inch) as shown in

Figure 4

,

Figure 5

, and

Figure 6

.

5.

Install the bagger mounting bracket to the rear frame
of the machine with 2 bolts (3/8 x 1-1/2 inches) (use
2 bolts (3/8 x 1 inch) for Z593 machines as shown in

Figure 5

), 2 curved washers (3/8 inch), and 2 flange

nuts (3/8 inch)as shown in

Figure 4

,

Figure 5

, and

Figure 6

.

Figure 4

For Z500 Gas Mowers

1.

Bolt (3/8 x 1-1/2 inches)

6.

ROPS

2.

Curved washer (3/8 inch)

7.

Flange nut (3/8 inch)

3.

Bagger mounting bracket

8.

Side view of bagger side
plate

4.

Spacer

9.

Holes for installing the
side bracket

5.

Bagger side plate

6

 

Содержание 78534





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды