manualshive.com logo in svg

Toro 78280, Руководство оператора

Поделиться
Скачать
Toro 78280 Скачать руководство пользователя страница 22

Maintenance

20

Greasing and Lubrication

Service Interval/Specification

Grease the mower after every 50 operating hours or
once a year, whichever occurs first. Grease more
frequently when operating conditions are extremely
dusty or sandy.

Grease Type: General-purpose grease.

How to Grease

1.

Disengage the power take off (PTO), set the
parking brake, and turn the ignition key to
“OFF” to stop the engine. Remove the key

2.

Clean the grease fittings with a rag. Make sure to
scrape any paint off the end of the fitting(s).

3.

Connect a grease gun to the fitting. Pump grease
into the fittings.

4.

Wipe up any excess grease.

Where to Add Grease

1.

Lubricate the blade spindles, idler pulley arm
and gage wheel bearings (Fig. 27).

M–2429

Figure 27

Blade Drive Belt

Removing the Blade Drive Belt

1.

Remove the mower; refer to Removing the
Mower, page 11.

2.

Remove pulley cover mounting screws and
pulley covers from both blade pulleys.

3.

Loosen idler spring and remove the belt from the
pulleys (Fig. 29).

Installing the Blade Drive Belt

1.

Install the new belt around the blade pulleys and
the idler pulley (Fig. 28).

m–2415

Figure 28

Содержание 78280





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды