Toro 74901 Z Master 5000 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 68

background image

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Change the engine oil.

After the first 100 hours

• Check the torque for wheel lug nuts.
• Check the wheel hub slotted nut torque.
• Check the torque for wheel lug nuts.
• Check the park brake adjustment.

After the first 250 hours

• Change the hydraulic filters and hydraulic oil when using any type of oil.

Before each use or daily

• Check the safety system.
• Check the engine oil level.
• Check the seat belt.
• Check the rollover protection system (ROPS) knobs.
• Clean the engine screen and the oil cooler.
• Check and clean the hydraulic unit shrouds.
• Check the mower blades.
• Clean the mower deck.

Every 50 hours

• Grease the mower deck spindles and idler arm.
• Check spark arrester (if equipped).
• Check the tire pressure.
• Inspect the belts for cracks and wear.
• Check the hydraulic oil level.

Every 100 hours

• Lubricate the mower deck lift pivots.
• Change the engine oil. (more often in dirty or dusty conditions)
• Check, clean and regap the spark plug.
• Check and clean engine cooling fins and shrouds.

Every 200 hours

• Change the engine oil filter.

Every 250 hours

• Replace the primary air filter (heavy duty air cleaner). (more often in dusty or sandy

conditions)

• Check the safety air filter (heavy duty air cleaner).
• Change the hydraulic filters and hydraulic oil when using Mobil® 1 oil (more often in

dirty or dusty conditions).

Every 500 hours

• Replace the safety air filter (heavy duty air cleaner).
• Replace the fuel filter. (more often in dirty or dusty conditions).
• Check the torque for wheel lug nuts.
• Check the wheel hub slotted nut torque.
• Check the torque for wheel lug nuts.
• Adjust the caster pivot bearing.
• Check the park brake adjustment.
• Change the hydraulic filters and hydraulic oil when using Toro® HYPR-OIL™ 500

hydraulic oil (more often in dirty or dusty conditions).

Monthly

• Check the battery.

Yearly

• Grease the pump belt idler arm.
• Grease the front caster pivots (more often in dirty or dusty conditions).
• Repack the front caster wheel bearings (more often in dirty or dusty conditions).
• Lubricate the caster wheel hubs

Yearly or before storage

• Paint chipped surfaces.
• Check all maintenance procedures listed above before storage.

Important:

Refer to your engine operator's manual for additional maintenance procedures.

30

«
...
28
29
30
31
32
...
»

Содержание 74901 Z Master 5000





































































Отзывы:

Нет отзывов

Похожие инструкции для 74901 Z Master 5000

Бренд: Snapper Страницы: 32

Бренд: Troy-Bilt Страницы: 28

Бренд: McCulloch Страницы: 100

sunjoe 24V-X2-21LM

Бренд: SNOWJOE Страницы: 68

Бренд: Ford Страницы: 156

Бренд: Dolmar Страницы: 132

Бренд: Dolmar Страницы: 128

Бренд: EMAK Страницы: 202

74926 Z Master G3

Бренд: Toro Страницы: 72

Super Recycler 21388

Бренд: Toro Страницы: 28

Бренд: Razarsharp Страницы: 17

Бренд: EINHELL Страницы: 128

Бренд: Jonsered Страницы: 24

STARIS E Series

Бренд: Exmark Страницы: 52

03863 Reelmaster 6500

Бренд: Toro Страницы: 24

Бренд: Viking Страницы: 229

Бренд: Toro Страницы: 32

Бренд: Nax Power Products Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды