manualshive.com logo in svg

Toro 74560, Руководство оператора

Поделиться
Скачать
Toro 74560 Скачать руководство пользователя страница 15

2.

Disengage the blades (PTO).

3.

Set the parking brake.

4.

Stop the engine and wait for all moving parts to stop.

5.

Remove the ignition key.

6.

Remove the grass collector; refer to Removing the
Grass Collector.

7.

Pull the drive control (located at the rear of the
machine) out to the Push position (Figure 14).

Note:

This disengages the drive system and allows

the wheels to turn freely.

G012449

2

1

Figure 14

1.

Push position

2.

Operate position

8.

Release the parking brake.

To Operate the Machine

1.

Set the parking brake.

2.

Push the drive control in to the Operate position
(Figure 14) to engage the drive system.

Note:

The machine will not drive unless the drive

control is in the Operate position.

3.

Install the grass collector; refer to Installing the Grass
Collector.

Driving the Machine Forward
or Backward

The throttle control regulates the engine speed as measured
in RPM (revolutions per minute). Place the throttle control in
the Fast position for best performance.

To go forward:

1.

Release the parking brake; refer to Releasing the
Parking Brake.

2.

Place your foot on the traction control pedal and slowly
press on the pedal to move forward (Figure 15).

G015677

1

2

Figure 15

1.

Forward control pedal

2.

Reverse speed pedal

Note:

To increase the speed, push the traction control

pedal down. To decrease the speed, release the pressure
on the traction control pedal.

To go backward:

1.

Release the parking brake; refer to Releasing the
Parking Brake.

2.

Place your foot on the reverse speed pedal and slowly
press on the pedal to move backward (Figure 15).

Note:

To increase the speed, push the reverse speed

pedal down. To decrease the speed, release the pressure
on the reverse speed pedal.

Important:

To avoid transmission damage, always

release the parking brake before moving the traction
control pedal or the reverse speed pedal.

Important:

To prevent damage to the mower, always

set the mower to the highest cutting position when you
drive the machine off the lawn.

Stopping the Machine

1.

Release the traction control pedal or the reverse speed
pedal.

2.

Disengage the blades (PTO).

Turn the ignition key to the Off position.

3.

Set the parking brake if you leave the machine
unattended; refer to Using the Parking Brake.

Note:

Remove the keys from the ignition and KeyChoice

switches.

15

Содержание 74560









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды