background image

Set Up instructions

5

POTENTIAL HAZARD

 Charging battery produces gasses.

WHAT CAN HAPPEN

Battery gasses can explode.

HOW TO AVOID THE HAZARD

Keep cigarettes, sparks and flames away
from battery.

4.

When the battery is fully charged, disconnect the
charger from the electrical outlet then from the
negative and positive battery posts (Fig. 6).

5.

Slowly pour electrolyte into each cell until the
level is once again up to the “UPPER” line on
the battery case (Fig. 5) and install covers.

6.

Install the battery in the tractor and connect
cables with (2) 1/4 x 3/4” bolts and (2) 1/4”
plastic wing nuts: refer to the Operator’s
Manual, Installing the Battery.

Crankcase Oil

Check the engine oil level, refer to the Operator’s
Manual, Engine Oil. If necessary, add only enough oil
to raise the level to the “FULL” mark on the dipstick.

Note:

Slide the oil dipstick fully into the
filler tube, do not thread onto fill tube.

Lubricate the Tractor

Refer to the Operator’s Manual, Greasing and
Lubrication.

If equipped with Power Lift, check reservoir level, fill
with Dexron Type II.

Check Safety System

Refer to the Operator’s Manual, Checking Safety
System.

Test Drive the Tractor

Make sure all electrical and mechanical systems are
operating properly.

Содержание 72071









Отзывы: