manualshive.com logo in svg

Toro 68021HD, Руководство оператора

Поделиться
Скачать
Toro 68021HD Скачать руководство пользователя страница 27

Premaintenance
Procedures

Preparing the Machine for
Maintenance

1.

Park the machine on a level surface.

2.

Remove the machine from the tow vehicle.

3.

Secure the machine from movement.

4.

Open the rear cowl; refer to

Opening the Cowl (page

18)

.

5.

Ensure that the engine and muffler are cool.

6.

Disconnect the spark-plug wire; refer to

Figure 35

.

Disconnecting the Spark-Plug
Wire

Pull the spark-plug wire off the terminal of the spark plug
(

Figure 35

).

G019281

1

Figure 35

1.

Spark plug

Removing and Installing the
Divider Plate

You need to remove the divider plate to provide access before
performing some maintenance procedures.

Removing the Divider Plate

1.

Unlatch and open the cowl; refer to

Opening the Cowl

(page 18)

.

2.

Use a wrench to remove the 4 bolts that secure the
divider plate to the front cowl.

Note:

Retain the bolts for installing the divider plate.

G020752

Figure 36

3.

To remove the divider plate, lift it upward and rotate
it counterclockwise so that it clears various engine
components.

Installing the Divider Plate

1.

Guide the divider plate into position against the front
cowl.

Note:

Start with the divider plate rotated slightly

counterclockwise, and then rotate it clockwise while
lowering it into position.
Ensure that the divider plate is not backward.

G020753

Figure 37

2.

Align the bolt holes in the divider plate and the front
cowl.

3.

Install the 4 bolts and hand-tighten them to prevent
cross-threading.

4.

Tighten the bolts with a wrench until they are secure.

27

 

Содержание 68021HD













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды