Toro 44912 Скачать руководство пользователя страница 28

3.

Remove the oil-filler cap/dipstick by rotating it
counterclockwise.

4.

Wipe the oil-filler cap/dipstick clean and insert it into
the filler port.

Note:

Do not screw the dipstick into the port.

5.

Remove the dipstick and check the oil level.

Note:

If the oil level is near or below the lower-limit

mark on the dipstick, add only enough oil to raise level
to the upper-limit mark (bottom edge of the oil-fill
hole); refer to

Figure 27

Check the oil level again. Do

not overfill the crankcase.

1

2

G024239

Figure 27

1.

Upper limit

2.

Lower limit

6.

Install the oil-filler cap/dipstick and wipe up any spilled
oil.

Note:

Running the engine with the oil level at the lower

limit may induce nuisance engine shutdowns in operating
situations where the machine is switching direction on an
incline or decent.

Changing the Engine Oil

Service Interval:

After the first 20 hours—Change the

engine oil.

Every 100 hours—Change the engine oil.

1.

Start and run the engine for a few minutes to warm the
engine oil; then stop the engine.

2.

Raise the machine onto the transport wheels.

3.

Tilt the machine so that the end of the machine with
the engine is closer to the ground, and support the
other end to hold it in this position.

4.

Install the drain hose onto the engine-oil-drain valve
(

Figure 28

).

5.

Place the other end of the hose into a suitable container
for oil (

Figure 28

).

1

2

3

4

5

6

G025538

Figure 28

6.

Turn the oil drain valve 1/4 turn counterclockwise to
start draining the oil (

Figure 28

).

7.

When all the oil is drained, turn the oil drain valve 1/4
turn clockwise to close the valve (

Figure 28

).

8.

Remove the drain hose and wipe any oil that may have
spilled.

9.

Fill the crankcase with the specified oil; refer to

Engine

Oil (page 27)

.

10.

Dispose of the oil properly. Recycle it as per local
codes.

Servicing the Air Cleaner

Service Interval:

Before each use or daily—Check the air

cleaner.

Every 50 hours—Clean the air cleaner (more often in
dirty or dusty conditions).

Every 300 hours—Replace the paper element.

1.

Disconnect the spark-plug wire from the spark plug.

2.

Remove the wing nut securing the air-cleaner cover to
the air cleaner, and remove the cover (

Figure 29

).

28

 

Содержание 44912





































Отзывы: