manualshive.com logo in svg

Toro 38428, Руководство оператора

Поделиться
Скачать
Toro 38428 Скачать руководство пользователя страница 18

18

2

644

1

Figure 19

1.

Scraper

2.

Carriage bolts and
locknuts (3)

6. Install the new scraper to the housing using the

carriage bolts and locknuts.

Replacing the Drive Belt

Inspect the drive belt before each season, and replace it if
it is worn or damaged.

1. Stop the engine.

2. Remove three self tapping screws, two capscrews, one

washer, and two locknuts that secure the belt cover to
the snowthrower frame (Fig. 20). Set the drive belt
cover aside.

1

2

3

4

631

Figure 20

1.

Cap screw, locknut

2.

Capscrew, locknut,
washer

3.

Long self tapping screw

4.

Short self tapping screws

3. Push down on the idler pulley and remove the drive

belt from the rotor pulley, the brake arm assembly, and
the engine pulley (Fig. 21).

4. Loop the new drive belt around the engine pulley,

under the idler pulley, over the roller, through the
brake assembly, and around the rotor pulley (Fig. 21).

4

2

1

6

3

5

626

Figure 21

1.

Engine pulley

2.

Idler pulley

3.

Roller

4.

Brake arm assembly

5.

Rotor pulley

6.

Belt guide

IMPORTANT: The drive belt must be on top of the roller
as shown in Figure 21.

5. Install the drive belt cover. Tighten the fasteners

securely, but do not overtighten.

Replacing the Spark Plug

Before each season, check the spark plug. If the electrodes
in the center of the plug are dark or have deteriorated,
install a new NGK BPMR4A spark plug.

1. Remove three capscrews securing the control panel to

the housing (Fig. 22).

2. Remove the ignition key and lift off the panel,

allowing it to hang on the recoil rope.

643

1

2

Figure 22

1.

Control panel

2.

Mounting screws

Содержание 38428

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды