manualshive.com logo in svg

Toro 37771, Руководство оператора, Страница: 25 / 32

Поделиться
Скачать
Toro 37771 Скачать руководство пользователя страница 25

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The power cord is disconnected at the

outlet or the machine.

1. Connect the power cord to the outlet

and/or the machine.

2. The power cord is worn, corroded, or

damaged.

2. Replace the power cord.

Electric starter does not turn (electric-start
models only)

3. The power outlet is not energized.

3. Have a qualified electrician energize

the outlet.

1. The key is not in the ignition or is in the

Stop position.

1. Insert the key into the ignition and turn

it to the On position.

2. The choke is in the Off position and the

primer has not been pressed.

2. Move the choke to the On position and

press the primer 3 times.

3. The fuel shutoff valve is not open.

3. Open the fuel shutoff valve.

4. The throttle is not in the Fast position.

4. Move the throttle to the Fast position.

5. The fuel tank is empty or the fuel

system contains stale fuel.

5. Drain and/or fill the fuel tank with fresh

gasoline (not more than 30 days old).
If the problem persists, contact an
Authorized Service Dealer.

6. The spark plug wire is loose or

disconnected.

6. Connect the wire to the spark plug.

7. The spark plug is pitted, fouled, or the

gap is incorrect.

7. Check the spark plug and adjust the

gap if necessary. Replace the spark
plug if it is pitted, fouled, or cracked.

8. The fuel vent cap is restricted.

8. Remove the vent restriction or replace

the fuel cap.

Engine does not start or starts hard

9. The engine oil level in the engine

crankcase is too low or too high.

9. Add or drain oil to adjust the oil level in

the engine crankcase to the Full mark
on the dipstick.

1. The choke is in the On position.

1. Move the choke to the Off position.

2. The fuel shutoff valve is not completely

open.

2. Open the fuel shutoff valve.

3. The fuel tank is nearly empty or

contains stale fuel.

3. Drain and fill the fuel tank with fresh

gasoline (not more than 30 days old).
If the problem persists, contact an
Authorized Service Dealer.

4. The spark plug wire is loose.

4. Connect the wire to the spark plug.

5. The spark plug is pitted, fouled, or the

gap is incorrect.

5. Check the spark plug and adjust the

gap if necessary. Replace the spark
plug if it is pitted, fouled, or cracked.

Engine runs rough

6. The engine oil level in the engine

crankcase is too low or too high.

6. Add or drain oil to adjust the oil level in

the engine crankcase to the Full mark
on the dipstick.

25

Содержание 37771

































Отзывы:

Нет отзывов