background image

Form No. 3434-434 Rev A

Universal Sunshade

Groundsmaster

®

or Reelmaster

®

Traction Units or Multi Pro

®

1750

Turf Sprayer

Model No. 30669

Model No. 30671

Installation Instructions

Important:

If you install the Universal Sunshade on a Reelmaster 3100 traction unit or a Groundsmaster

3500/3505 traction unit, install the Wheel Weight Kit. Contact your authorized Toro distributor for
the correct Wheel Weight Kit.

Safety

General

Before Operating

1.

Review and understand the contents of the

Installation Instructions

before installing the

sunshade.

2.

Keep all shields, safety devices and decals
in place. If a shield, safety device or decal
is defective, illegible, or damaged, repair or
replace it before operating the machine.

3.

Do not weld, cut, drill, modify, or remove the roll
bar in any manner.

4.

Tighten any loose nuts, bolts, or screws to
ensure that the machine is in safe operating
condition.

While Operating

1.

Use extreme care when working close to fences,
ditches, or on hillsides.

2.

Check carefully for overhead clearances (i.e.,
branches, doorways, electrical wires) before
driving under any objects and do not contact
them.

3.

Tie down the sunshade frame when transporting
the machine.

4.

Wear hearing protection when operating any
machine with a sunshade.

Maintenance and Service

1.

Before servicing or making adjustments, lower
the implement, shut off the engine, engage the
parking brake, and remove the key.

2.

Make sure that the machine is in safe operating
condition by keeping all nuts, bolts, and screws
tight.

3.

When working on the sunshade installation,
wear eye protection.

4.

Replace a damaged sunshade. Do not repair
or revise.

5.

When installing the sunshade or performing
service, use correct supports, hoists, and jacks.
If the sunshade is not properly supported, it may
move or fall, which may result in personal injury.

6.

To ensure optimum performance and safety,
always purchase genuine Toro replacement
parts and accessories. Replacement parts and
accessories made by other manufacturers could
be dangerous. Such use could void the product
warranty of The Toro Company.

© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3434-434* A

 

Содержание 30669





















Отзывы: