background image

Form No. 3429-505 Rev A

62in Blower Kit

Groundsmaster

®

200/3280-D/3320 Series Side Discharge Mowers

Model No. 30506—Serial No. 403000001 and Up

Operator's Manual

This product complies with all relevant European directives. For details, please see the Declaration of
Incorporation (DOI) at the back of this publication.

WARNING

CALIFORNIA

Proposition 65 Warning

Use of this product may cause exposure to chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm.

Safety

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decal93-6696

93–6696

1.

Stored energy hazard—read the

Operator's Manual

.

decal106-6753

106-6753

1.

Thrown object hazard—keep bystanders away.

2.

Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.

decal93-7301

93–7301

1.

Warning-read the

Operator's Manual.

2.

Thrown object hazard-stay away from moving parts; keep
all guards and shields in place.

decal107-2926

107-2926

1.

Cutting/dismemberment hazard of hand, impeller—stay
away from moving parts.

2.

Thrown object hazard—keep bystanders away.

decal133-8061

133-8061

© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3429-505* A

 

Содержание 30506





















Отзывы: