background image

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Inspect the blower belt.
• Inspect the collection system.

Before each use or daily

• Clean the hood screen.
• Clean the collection system.

Every 25 hours

• Inspect the blower belt.

Every 50 hours

• Grease the idler arm.

Every 100 hours

• Grease the handle pivot.
• Inspect the collection system.

Cleaning the Bagger Screen

Service Interval:

Before each use or daily

The screens need to be cleaned before each use. In wet grass
they will need to be cleaned more often.

1.

Disengage the power take off (PTO) and set the
parking brake.

2.

Turn off the engine, remove the key, and wait for all
moving parts to stop before leaving the operating
position.

3.

Open the bagger.

4.

Clean the debris from the screen.

5.

Close the bagger.

Cleaning the Collection
System

Service Interval:

Before each use or daily

1.

Wash the inside and outside of the bagger hood, tube,
and the underside of the mower. Use a mild automotive
detergent to remove dirt.

2.

Make sure you remove matted grass from all parts.

3.

After washing all parts, let them dry thoroughly.

Note:

With all parts installed, start and run the machine for

a minute to assist in drying.

Inspecting the Blower Belt

Service Interval:

After the first 8 hours

Every 25 hours

Check belts for cracks, frayed edges, burn marks or any other
damage. Replace damaged belts.

Replacing the Blower Belt

1.

Disengage the PTO, move the motion control levers to
the neutral locked position, and set the parking brake.

2.

Stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.

3.

Pull back on the spring loaded idler pulley to relieve
the belt tension (

Figure 35

).

4.

Remove the existing blower belt from the mower deck
pulley and then the blower pulleys.

5.

Install the new belt around the blower pulleys and the
mower deck pulley (

Figure 35

).

Figure 35

1.

Idler pulley

4.

Peg

2.

Mower deck pulley

5.

Belt

3.

Spring

6.

Blower pulley

6.

Install the spring as shown in

Figure 36

.

22

 

Содержание 30460

































Отзывы: