Toro 29645 Скачать руководство пользователя страница 13

Servicing the Air Cleaner

Service Interval:

Every 25 hours/Yearly (whichever comes

first)—Replace the air cleaner element
(more frequently when operating the
machine in dusty or dirty operating
conditions).

1.

Press the top tab on the air cleaner cover (

Figure 17

)

and open the cover.

Figure 17

1.

Top tab on the cover

5.

Cover

2.

Air-cleaner body

6.

Bottom tab (2)

3.

Post (2)

7.

Air-cleaner element

4.

Latch

8.

Slot (2)

Note:

You do not need to remove the cover from the

air-cleaner body; you can leave the bottom tabs of the
cover in the slots of the air-cleaner body.

2.

Remove the air-cleaner element (

Figure 17

).

3.

If the air-cleaner element is damaged or is wet with
oil or fuel, replace it.

Note:

Install the air-cleaner element by aligning it with

the posts on the air-cleaner body.

4.

Install the cover.

Changing the Engine Oil

Service Interval:

After the first 5 hours

Yearly

Run the engine a few minutes before changing the oil to warm
it. Warm oil flows better and carries more contaminants.

1.

Perform the pre-maintenance procedures; refer to

Preparing for Maintenance (page 12)

.

2.

Remove the dipstick.

3.

Tip the machine onto its side, with the dipstick down,
to drain the used oil out through the oil-fill tube (

Figure

18

).

Figure 18

4.

After draining the used oil, return the machine to the
normal operating position.

5.

Pour about 3/4 of the crankcase capacity of oil into
the oil-fill tube.

Note:

Max. fill: 0.55 L (18.6 oz), type: SAE 30 or SAE

10W-30 detergent oil with an API service classification
of SF, SG, SH, SJ, SL, or higher.

6.

Wipe off the dipstick end with a clean cloth.

7.

Insert the dipstick into the oil-fill tube, but

do not

screw it in.

8.

Remove the dipstick and read the oil level on the
dipstick (

Figure 19

).

Figure 19

If the oil level is low, add a small amount of oil
slowly to the oil-fill tube, and then repeat steps

6

through

8

until the oil level on the dipstick is

correct.

If the oil level is high, drain the excess oil until the
oil level on the dipstick is correct.

Important:

If the oil level in the crankcase is

too low or too high and you run the engine,
you may damage the engine.

13

 

Содержание 29645





















Отзывы: