manualshive.com logo in svg

Toro 23511, Руководство оператора

Поделиться
Скачать
Toro 23511 Скачать руководство пользователя страница 20

Belt Maintenance

Checking the Belt Tension

Service Interval:

Before each use or daily—Check

the belt tension. If the engine is
working but the cutting blades
seem underpowered, check the belt
tension.

1.

Park the machine on a level surface, disengage
the cutting blades, shut off the engine, and wait
for all moving parts to stop, turn the engine
switch to the O

FF

position, and raise the cutting

blades to the transport position.

2.

Disconnect the wire from the spark plug.

3.

Stop the machine on a level surface, stop the
engine by releasing the operator presence bail,
disconnect the spark-plug wire,

4.

Remove the 4 bolts securing the belt cover to
the left side of the machine and remove the
cover (

Figure 21

).

g020749

Figure 21

1.

Belt

3.

Bolts

2.

Cover

5.

Check the tension of the belt (

Figure 21

).

Note:

The belt should not flex more than a 12

mm (1/2 inch) with moderate finger pressure
applied to the span just above the machine
frame.

6.

If the belt tension is loose, refer to

Adjusting the

Belt Tension (page 20)

.

7.

Install the belt cover before operating the
machine.

Adjusting the Belt Tension

1.

To tighten the belt, loosen the 4 mounting nuts
securing the engine to the frame.

g019740

Figure 22

1.

Mounting nuts

2.

Move the engine to tighten the belt to the proper
tension.

3.

Secure the 4 mounting nuts and bolts.

Note:

Torque the bolts that secure the engine

to the frame 271 N∙m (200 in-lb).

20

 

Содержание 23511

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды