manualshive.com logo in svg

Toro 23511, Руководство оператора

Поделиться
Скачать
Toro 23511 Скачать руководство пользователя страница 15

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 25 hours

• Change the engine oil.

Before each use or daily

• Clean debris form the machine.
• Inspect the air-cleaner elements.
• Check the engine-oil level.
• Check the belt tension. If the engine is working but the cutting blades seem

underpowered, check the belt tension.

• Check the blades for wear or damage.
• Check for loose fasteners.

Every 50 hours

• Clean the air-cleaner elements. Clean them more frequently in dusty operating

conditions.

Every 100 hours

• Change the engine oil.
• Clean the sediment cup.
• Inspect, clean, and adjust the spark plug; replace it if necessary.

Every 200 hours

• Replace the spark plug.

Every 300 hours

• Replace the paper air-cleaner element. Replace it more frequently in dusty

operating conditions.

Yearly or before storage

• Touch up chipped paint.

Pre-Maintenance
Procedures

Disconnecting the
Spark-Plug Wire

Before performing any maintenance on the engine,
belts, or cutting blades, disconnect the spark-plug
wire from the spark plug (

Figure 12

).

g019426

Figure 12

1.

Spark-plug wire

15

 

Содержание 23511

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды