manualshive.com logo in svg

Toro 23511, Руководство оператора


Поделиться
Скачать
background image

Seeding-Rate Gauge

Use the seeding-rate gauge to set the seed flow rate.
It is calibrated with the machine speed to give you
an even seeding rate at any speed. To change the
seeding rate, loosen the knob on the gauge and move
the gauge pointer to the desired position, then tighten
the knob to hold it in place.

g013146

Figure 9

Refer to the seeding graph located on the machine
to determine the correct gauge setting for the type
of grass you are planting and the thickness in which
you want to plant it.

Seed-Gate-Control Lever

Push the seed-gate-control lever (

Figure 10

) forward

to start the seed flow, and pull it rearward to stop the
seed flow.

Note:

The machine is designed so that the seed flow

slows and/or stops when you stop the machine or
slow for a turn. To reduce seed loss, raise the front
wheels as the machine is turned. There is no need to
turn the seed flow on and off for each turn.

g241995

Figure 10

1.

Seed-gate-control lever

11

 

Содержание 23511

























Отзывы:

Нет отзывов

Похожие инструкции для 23511

Daihen OTC CM-743-U Owner'S Manual preview
OTC CM-743-U
Бренд: Daihen Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды