Toro 139-5636 Скачать руководство пользователя страница 10

Preparing the Machine for
Maintenance

WARNING

While you are maintaining or adjusting the
machine, someone could start the engine.
Accidentally starting the engine could
seriously injure you or other bystanders.

Remove the key from the ignition, engage
parking brake, and pull the wire(s) off the
spark plug(s) before you do any maintenance.
Also push the wire(s) aside so it does not
accidentally contact the spark plug(s).

Perform the following before servicing, cleaning, or
making any adjustments to the machine.

1.

Park the machine on a level surface.

2.

Shut off the engine and remove the key from the
machine (if equipped).

3.

Engage the parking brake.

4.

Wait for all moving parts to stop and allow the
engine to cool before servicing or storing.

5.

Disconnect the spark-plug wire (

Figure 13

).

g265998

Figure 13

1.

Spark-plug wire

Servicing the Engine Oil

Fill the crankcase with approximately 0.56 L (19 fl
oz) of the proper viscosity oil before starting. The
engine uses a high-quality oil that has the American
Petroleum Institute (API) service classification of SJ or
higher. Select the proper oil viscosity (weight) based
on the ambient temperature.

Figure 14

illustrates the

temperature/viscosity recommendations.

g013375

Figure 14

Note:

Multi-grade oils (5W-20, 10W-30 and 10W-40)

increase oil consumption. Check the engine-oil level
more frequently when you use these oils.

Checking the Engine-Oil Level

Service Interval:

Before each use or daily

The ideal time to check the engine-oil level is when the
engine is cool or before you have started the engine
for the day. If you have already ran the engine, allow
the oil to drain back down to the sump for at least 10
minutes before you check the engine-oil level.

1.

Shut off the engine and wait for all moving
parts to stop; refer to

Preparing the Machine for

Maintenance (page 10)

.

2.

Position the machine so that the engine is level,
and clean the area around the oil-fill tube (

Figure

15

).

10

 

Содержание 139-5636

















Отзывы: