background image

Configuration: Tricycle vehicle with welded steel
frame construction. Rear engine placement. All
wheels powered.

Engine: Briggs & Stratton, V-twin cylinder, 4-cycle,
OHV, air-cooled, gas engine with cast iron sleeves.
16 hp @ 3600 rpm, 29.3 cu. in. (480 cc) displace-
ment, 1.75 qt. oil capacity. Electronic ignition. Full
pressure lubrication, oil filter. Engine and remote-
mounted air cleaners.

Gauges: Ammeter and hour meter.

Controls: Hand-operated throttle, choke and lift
lever. Foot pedal controls traction forward/reverse
speed.

Steering: Front wheel steering with adjustable tilt
steering wheel.

Gas Tank: 5.5 gallon capacity.

Battery: 12-volt, lead acid, 32 amp hour.

Drive: Hydraulic. Coupling driven variable displace-
ment piston pump with integral auxiliary charge
pump to hydraulic motors which directly drive
wheels.

Hydraulic Oil Filter: 25 micron, spin-on type.

Hydraulic Oil Reservoir: 3 gallon capacity.

Valve: Single section for raising and lowering of
implement.

Cylinder: Double acting.

Tires: 22 x 11.00 - 8 two-ply pneumatic tubeless.
De-mountable and interchangeable. Recommended
tire pressure is 4 PSI.

Speeds (at 3200 RPM): Variable between 0 and 8.5
MPH forward and 0 and 4 MPH reverse.

Seat Adjustment: 4 inches - fore and aft. Additional
1.75 inches forward adjustment available by using
front mounting holes. Additional adjustment for
small operator attained by removing the seat slides
and base and mounting the seat directly to support.

Dimensions: 

Width w/o implements:

58”

Width w/rake (Model 08812):

75”

Height: 46.25”
Length w/o implements: 

70.75”

Wheelbase

42.75”

Net Weight: (Wet)

807 lb.

Optional Equipment:

Drag Mat, Model 08845
Edger, Model No. 08822
Rake, Model No. 08811
Rake Mounting Kit, Model No.08814
Tooth Rake, Model No. 08812
Weeder/Cultivator, Model No. 08815
Finish Grader, Model No. 08867
Spiker, Model No. 08856
Prong Rake Attachment, Part No.42-3960
Hitch, Part No. 20-3900
Front Blade, Model No.08821
Renovation Cultivator, Model No. 08818
Two Speed Valve Kit, Part No. 88-8500

8

Specifications

Содержание 08881 SAND PRO 5000





























Отзывы: