manualshive.com logo in svg

Toro 08839, Руководство оператора

Поделиться
Скачать
Toro 08839 Скачать руководство пользователя страница 26

Adjusting the Height of the
Mid-Mount Attachment

Raising the Mid-Mount Attachment

1.

Park the machine on a level surface and engage
the parking brake.

2.

If you want to fully raise the mid-mount
attachment remove the stop pin from the up-stop
attachment-stop hole, and insert it into the
stow attachment-stop hole; refer to

Mid-Mount

Attachment Stop (page 30)

.

3.

With the engine running, pull back the mid-mount
attachment lift control to raise the mid-mount
attachment(

Figure 31

).

g384220

g358791

Figure 31

1.

Mid-mount attachment control

Lowering the Mid-Mount
Attachment

1.

Park the machine on a level surface.

2.

If needed, adjust the mid-mount attachment
stop depth; refer to

Using the Attachment Stop

During Operation (page 33)

.

3.

With the engine running, push forward the
mid-mount attachment lift control to lower the
mid-mount attachment (

Figure 32

).

g384219

g358800

Figure 32

1.

Mid-mount attachment control

26

 

Содержание 08839

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды