Toro 08839 Скачать руководство пользователя

Страница: 18 / 64

Parking Brake and Motion Control

g384036

Figure 23

Parking brake handle

Front reference bar

Motion-control bars

Rear reference bar

Parking-Brake Handle

Use the parking brake handle (

Figure 23

) to engage

and disengage the parking brake.

The parking-brake handle is located on the control
tower, to the left of the front reference bar.

Motion-control bars

The motion-control levers (

Figure 23

) are located at

each side of the top control tower, and control the
forward and reverse motion of the machine

Move the levers forward or backward to control the
drive wheel on the same side forward or reverse
respectively. The wheel speed is proportional to the
amount you move the lever.

Specifications

Length

292.3 cm (115 inches)

Width

(without mid-mount

attachment installed)

147.3 cm (58 inches)

Width

(with multi–tool

attachment installed)

172.7 cm (68 inches)

Height

129.5 cm (51 inches)

Net weight

(empty with no

options installed)

521.6 kg (1,150 lbs)

Net weight

(with multi–tool

attachment installed)

734.8 kg (1,620 lbs)

Maximum forward speed

16 km/h (10 mph)

Maximum reverse speed

8 km/h (5 mph)

Содержание 08839

































































Результаты поиска

Содержание 08839

Отзывы:

Похожие инструкции для 08839

Бренды по названию

Популярные бренды

Toro 08839, Руководство оператора

Результаты поиска

Содержание 08839

Отзывы:

Похожие инструкции для 08839

Бренды по названию

Популярные бренды