Toro 07059LT Скачать руководство пользователя страница 12

Страница: 12 / 60

Controls

Become familiar with all the controls before you start the engine and operate the machine.

Control Panel

g033921

Figure 6

Steering wheel

USB power point

Gear-shift indicator

Parking-brake lever

Gear-shift lever

Choke control

Horn button

Brake pedal

Key switch

10.

Accelerator pedal

Accelerator Pedal

Use the accelerator pedal (

Figure 6

) to vary the

ground speed of the machine. Pressing down the
accelerator pedal starts the engine. Pressing the
pedal farther increases the ground speed. Releasing
the pedal slows the machine, and the engine shuts off.

Note:

The maximum forward speed is 26 km/h

(16 mph).

Brake Pedal

Use the brake pedal to stop or slow the machine
(

Figure 6

CAUTION

Operating a machine with worn or incorrectly
adjusted brakes can may result in personal
injury.

If the brake pedal travels to within 25 mm (1
inch) of the machine floor board, adjust or
repair the brakes.

Содержание 07059LT





























































Результаты поиска

Содержание 07059LT

Отзывы:

Похожие инструкции для 07059LT

Бренды по названию

Популярные бренды

Toro 07059LT, Руководство оператора

Результаты поиска

Содержание 07059LT

Отзывы:

Похожие инструкции для 07059LT

Бренды по названию

Популярные бренды