background image

5. FILTER CLEANING 

 

The filter must be cleaned from time to time. This must be done before changing the 

bag collection system and should also be done when work is completed or when there 

is poor suction. 

 

Procedure:   

1. Push down the damper , cover the inlet. 

2. Turn on the machine and wait 3 seconds, let the   

machine build up vacuum. 

3. Quickly push down on the key and wait 3 seconds. 

4. Repeat the procedure five times.   

5. Turn off the motor and wait until it stops completely,   

then uncover the inlet.

 

 

 

   

If suction remains poor, the pre-filter needs to be replaced. If suction still remains 

poor afterwards, the HEPA filters needs to be replaced. See instructions in chapter 6. 

FILTER CHANGE. 

 

6. DUST STORAGE SYSTEM 

 

The dust extractors are mainly equipped with continuous folding bagging  system for 

effective dust storage or  a regular plastic bag system depending on model. The 

continuous bag is a 22 m long plastic tube that will be divided into plastic bags using the 

zip ties attached with the machine. 

 

To assemble a new continuous bag:   

Release the belt holding the last bag. Remove the holder, put in a new bag & pull out 

the inner end upwards. Assemble the holder on to the machine and strap the opening 

facing upwards with the belt. Pull down the outside end and close it using a zip tie. 

 

All dust extractors can be used with continuous folding dust bags for single use. Also all 

models can be fitted with the continuous bag system. 

 

Only change continuous bag or regular bag after filter cleaning cycle have been 

completed. 

 

To operate the continuous bag: 

 

 

 

 

 

 

 

7. FILTER CHANGE 

 

Risk of dust dispersion - Use personal safety equipment 

 

Unhealthy dust can be spread during filter change. Accordingly, the user should wear 

protective glasses, protective gloves, and a breathing mask conforming to protection class 

FFP3. 

 

 

 

 

 

1.

 

Assemble the continuous bag, turn on the   

   machine. 

2.

 

Turn off the machine, the dust will drop down   

   to the bags. 

3.

 

Use a nylon tie to seal the bag 

4.

 

Cut the bag 

 

!!!

  It is important to let the machine rebuild the vacuum in between every repetition. 

 

 

Содержание TIV2000
















Отзывы: