Torklift central X7910 Скачать руководство пользователя страница 20

 

 

Page 
19

 

 

 

 

 
Although Torklift Central trailer hitches are both tested and rated for 
towing within the specific capacity label found on each trailer hitch. 
Torklift Central assumes no liability for vehicle manufacturers 
warranty due to the use of a Torklift Central trailer hitch being used 
for towing behind any vehicle or using the trailer hitch in a manner 
that it was not designed for. Although this specific trailer hitch has a 
load rating, which includes trailer tongue weight, and a trailer weight 
carrying capacity, Torklift Central is not responsible for the voiding 
of any warranty on any vehicle due to factory towing limitations. All 
vehicle warranties are the sole property and responsibility of the 
owner of the vehicle that the Torklift Central trailer hitch is installed 
upon. Torklift Central does not endorse towing behind any vehicle if 
the vehicles manufacturer states that towing is not recommended. 
Check your vehicle’s owner’s manual for the proper tow rating of 
your vehicle.  

 

ADDRESS:  

315 Central Ave N. Kent, WA 98032

 

 
*WARNING*

 

Your vehicle may have a lower tow rating than this 

trailer hitch. If your vehicle’s tow rating is less than the rated towing 
capacity on your Torklift Central trailer hitch, your trailer hitch 
capacity is limited to your vehicle’s factory rated towing capacity. 
 

*DANGER* 

Never exceed your vehicle's manufacturer's 

recommended towing capacity which may be a lower rating than this 
trailer hitch 

 

Содержание X7910





















Отзывы: