URL:
Name: HMT028ATB-C-Manual-Rev0.3
Page: 11 of 14
cause the display color change abnormally.
-
LCD panel is made with glass. Any mechanical shock (e.g.
dropping from high place) will damage the LCD module.
-
-
液晶屏由玻璃制作而成，任何机械碰撞
(
如从高处跌落
)
均有可能损坏液晶显示模块。
-
Protective film is attached on LCD screen. Be careful when
peeling off this protective film, since static electricity may
be generated.
-
Polarizer on LCD gets scratched easily. If possible, do not
remove LCD protective film until the last step of
installation.
-
When peeling off protective film from LCD, static charge
may cause abnormal display pattern. The symptom is
normal, and it will turn back to normal in a short while.
-
LCD panel has sharp edges, please handle with care.
-
Never attempt to disassemble or rework LCD module.
-
If display panel is damaged and liquid crystal substance
leaks out, be sure not to get any in your mouth, if the
substance comes into contact with your skin or clothes
promptly wash it off using soap and water.
7 CTP Mounting Instructions
7.1 Bezel Mounting (Figure 1)
-
The bezel window should be bigger than the CTP active
area. It should be≥0.5mm each side.
-
Gasket should be installed between the bezel and the CTP
surface.
The final gap should be about 0.5~1.0mm.
-
It is recommended to provide an additional support
bracket for backside support when necessary (e.g. slim
type TFT module without mounding structure). They
should only provide appropriate support and keep the
module in place.
-
The mounting structure should be strong enough to
prevent external uneven force or twist act onto the
module.
-
液晶屏表面带有保护膜
,
揭除保护膜时需要注意可能产
生的静电。
-
-
因液晶显示屏表面的偏光片极易划伤，安装完成之前请
尽量不要揭下保护膜。
-
-
请缓慢揭除保护膜，在此过程中液晶显示屏上可能会产
生静电线，此为正常情况，可在短时间内消失。
-
-
请注意避免被液晶显示屏的边缘割伤。
-
请不要试图拆卸或改造液晶显示模块。
-
当液晶显示屏出现破裂
,
内部液晶液体可能流出
;
相关
液体不可吞吃
,
绝对不可接触嘴巴
,
如接触到皮肤或衣
服
,
请使用肥皂与清水彻底清洗
.
-
7.
电容触摸屏安装指导
7.1
面框安装（附图
1
）
-
客户面框窗口应大于
CTP
动作区域，各边离动作区应
≥
0.5mm.
-
面框与
CTP
面板间应垫有胶垫，其最终间隙约为
0.5
～
1.0mm.
-
-
建议必要时在背面提供附加支架
(
例如无安装结构的薄型
TFT
模块
)
，应仅利用适当支撑以保持模块位置
.
-
安装结构应具有足够的强度，以防止外部不均匀力或扭
曲力作用到模块上
.
Figure 1
7.2 Surface Mounting (Figure 2)
-
As the CTP assembling on the countersink area with
double side adhesive.
The countersink area should be flat and clean to ensure
the double side adhesive installation result.
-
The Bezel is recommend to keep a ga
p (≥0.3mm each
side) around the cover lens for tolerance.
-
It is recommended to provide an additional support
bracket with gasket for backside support when necessary
(e.g. TFT module without mounding structure). They
should only provide appropriate support and keep the
module in place.
-
The mounting structure should be strong enough to
prevent external uneven force or twist act onto the module
7.2
嵌入安装（附图
2
）
-
客户面框应具有使用双面胶粘贴
CTP
的结构沉台面，其
粘贴面要求平整且洁净无污以保证粘贴牢靠
.
-
考虑到制作误差，建议面框与
CTP
盖板之间四周留有
≥
0.3mm
间隙
.
-
建议必要时在背面提供垫有胶垫附加支架
(
例如无安装结
构的
TFT
模块
)
，应仅利用适当支撑以保持模块位置
.
-
安装结构应具有足够的强度，以防止外部不均匀力或扭
曲力作用到模块上。
Содержание HMT028ATB-C
Страница 14: ......
