manualshive.com logo in svg

Toptech T915, Руководство по установке

Поделиться
Скачать
Toptech T915 Скачать руководство пользователя страница 5

WIRING

5

Caution: Electrical Hazard

Failure to disconnect the power 
before beginning to install this 
product can cause electrical 
shock or equipment damage.

Warning:

All components of the control 
system and the thermostat 
installation must conform to 
Class II circuits per the NEC Code.

Wire specifications

Use shielded or non-shielded 
18 - 22 gauge thermostat wire.

C terminal

The C (common wire) terminal does 
not have to be connected when the 
thermostat is powered by batteries.

PRO1 Tips:

Wiring

Terminal Designations

If you are replacing a thermostat, make 

note of the terminal connections on the 

thermostat that is being replaced. In some 

cases the wiring connections will not be 

color coded. For example, the green wire 

may not be connected to the 

G terminal.

Loosen the terminal block screws. Insert 

wires then retighten terminal block screws.

Place nonflammable insulation into wall 

opening to prevent drafts.

1.

2.

3.

Heat relay, Stage 1

Heat relay, Stage 2

Compressor relay, Stage 1

Compressor relay, Stage 2

Fan relay

Heat pump changeover valve 

energized in cooling

Transformer power for heating

Heat pump changeover valve 

energized in heating

Common wire from system transformer

W1

W2

Y1

Y2

G

O

R

B

C

Содержание T915














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды