Topper TOPAZ XENON Скачать руководство пользователя | Manualshive

Страница: 6 / 21

background image

5

12

Then attach the foot of the jib to the Furler at the front of the boat (ensure the
Furler is fully wound up). Attach jib head to the swivel on jib Halyard.

Tape the split rings without impeding the action of the Furler.

Make sure you are still head to wind.

«
...
4
5
6
7
8
...
»

Содержание TOPAZ XENON






















Отзывы:

Нет отзывов

Похожие инструкции для TOPAZ XENON

Бренд: Tayana Страницы: 85

Бренд: Feathercraft Страницы: 8

Бренд: J&J Amusements Страницы: 171

Бренд: Sea-doo Страницы: 130

2014 Spark Series

Бренд: Sea-doo Страницы: 148

230 Challenger 2008

Бренд: Sea-doo Страницы: 160

Бренд: GALA Страницы: 10

Бренд: Palfinger Страницы: 259

Бренд: RIOT Страницы: 7

Бренд: BENETEAU Страницы: 43

Бренд: Cal Boats Страницы: 49

Бренд: UK Sailmakers Страницы: 5

Бренд: Malibukayaks Страницы: 15

Бренд: Axopar Страницы: 118

Бренд: Ranger boats Страницы: 36

Бренд: SeaDoo Страницы: 7

Бренд: SeaDoo Страницы: 60

Бренд: Lund Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды