PEAK
PEAK
MUTE
MUTE
SUB 1 2
-
SUB 1 2
-
SUB 3 4
-
SUB 3 4
-
MAIN L R
-
MAIN L R
-
10
10
dB
dB
-5
-5
-10
-10
-20
-20
-25
-25
-30
-30
0
0
5
5
SOLO
SOLO
-40
-40
-60
-60
4
5 6
/
FREQ
MID
BAL
80Hz
80Hz
LOW
LOW
800
100Hz
8KHz
EQ
EQ
HI
HI
12kHz
12kHz
HI MID
-
3kHz
500Hz
MID LOW
-
1
1
2
2
PRE
PRE
POST
POST
DFX2
4
DFX2
4
3
DFX1
3
DFX1
This is a peaking filter and it will boost/cut frequencies from 100 Hz to 8 kHz
depending on the position of the MID freq control. This control will affect
especially upper male and lower female vocal ranges and also the harmonics
of most musical instruments.
11- MID
12- HI-MID
13- MID-LOW
14- LOW
15- AUX SENDS Level Control
These four controls are used to adjust the
level of the respective signal sent to AUX
bus, AUX1 and AUX2 can be switched to
PRE/POST-FADER via the PRE/POST button,
so, generally, they can be used for monitor
16- PAN/BAL Control
Abbreviation of PANORAMA control for mono channels, or the stereo channels,
always says, BALANCE control. Keep this control in center position, then the
signal will be positioned in the middle of stage.
CONTROL ELEMENTS
This control gives you up to 15 dB boost
or cut at 3 kHz. It is useful for controlling
voice. It can accurately polish your perfo-
rmance via adjusting this knob.
This control gives you up to 15 dB boost
or cut at 500 Hz.
If you turn this control up, you will boost
all frequencies below 80 Hz. You will give
more punch to bass drum and bass guitar
and make the vocalist more "macho". Turn
it down, you will cut all the frequencies
below 80 Hz. In this way, you can avoid
low frequency vibrations and resonance
thus preserving the life of your woofers.
application and effects & sound processors input. AUX3 and AUX4 are
configured as POST-Faders. In this typical compact unit, excluding sending
out the signal directly to the external effect or processor equipment, AUX
SEND4 can also be assigned to the internal onboard effect module.
18
20
12
13
10
11
14
15
16
17
19
OPTION MODULES
For connecting with USB memory.
In pause state, press this button it will go to the previous song and keep
in pause state. In play state, press this button it will go to the previous song
and start playing.
In pause state, press this button it will go to the next song and keep in
pause state. In play state, press this button , it will go to the next song
and start playing.
The file system of USB memory for USB-MP3 player is FAT16 and FAT32. The
player can only decode MP3. It can have 7 rank subordinate folders at most,
and the maximum quantity of folders within MP3 files is 24. In the whole USB
memory, the total folders can not beyond 256(incluing those folders without
MP3 songs).
Press this button the player will change between the following four modes. REP
ALL means to repeat all songs in the memory, the mark on the screen is
.
REP1 means to repeat one song, the mark on the screen is
Play in order
means to play the songs according to the order, the mark on the screen is
blank. Random play means to play the songs at random, the mark on the
screen is A.
.
all
1
1
1
1
1
62- USB PORT
63- PREVIOUS
64- NEXT
65- REPEAT
MP3 player module
install
Put the MP3 player module connection wire into MP3MOD CONNECTOR. Fix the
MP3
at one of the two module places with the two attached screws.
player module
function
62
63
64 65
67
66
68
MIX
MIX
4
5
7
16
USB PLAYER
(Push & Hold)
POWER
TAC-MP3-T
