TOPMAQ 36087 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

TOPMAQ 36087 Скачать руководство пользователя страница 17

WOOD CHIPPER

17

GB

Make sure the machine is level
and stable to avoid unnecessary
vibrations.

The engine is fitted with an oil alert
and will not start if the oil level in the
sump is too low. It may also stop if it
is operated on a steep slope.

To shut down the machine, move
the throttle control lever to idle
speed, turn the engine switch to the
OFF position, and it will gradually
come to a standstill.

Do not operate on concrete or other
hard surface.

the machine until the engine has returned to
full speed.

The chipper shredder can clog up with soft,
wet, or fibrous materials. However, if you feed
soft materials intermittently with branches,
there should be no problem, as the chipper
shredder tends to clean out any residue left in
the machine.

If any stringy material wraps around the rotor
shaft, remove it before it works its way into the
bearing.

If the chipper shredder stalls from overloading
or clogging, turn off the engine’s power switch
and wait until the cutting disk is completely
stopped and the belt drive is disengaged. Allow
the engine to completely cool and switch the
engine to off. Open the housing cover to clear
and remove all the materials from the housing.
Lock the housing cover, switch the engine to
the on position, and start the machine again to
resume operation.

As the discharge material plies up, move the
chipper away from the pile. This will keep the
material from backing up the discharge chute.
Do not position the deflector vertically, as this
will reduce the airflow, impeding the discharge
and causing blockage.

S u d d e n s t o p p i n g a t a h i g h
speed under a heavy load is not
recommended. Engine damage may
result.

Do not move the choke control to
CLOSE to stop the engine. Backfire
or engine damage may occur.

Idle Speed

Set the throttle control lever to the SLOW
position to reduce stress on the engine when
chipping is not being performed. Lowering the
engine speed will help extend the life of the
engine, as well as conserve fuel and reduce
noise level.

Stop Engine

To stop the engine in an emergency, simply
turn the engine switch to the OFF position.
Under normal conditions, use the following
procedure:

1. Move the throttle lever to the SLOW (

)

position.

2. Let the engine idle for one or two minutes.

3. Turn the engine switch to the OFF position.

4. Turn the fuel valve lever to the OFF (

)

position.

Emergency Stop

Make sure the emergency stop switch is
working before every use. Otherwise serious
injury or death may occur. Note that the
emergency stop wire should be routed around
the left side of the hopper as you look at it.

Emergency Stop Handle

EMERGENCY STOP

36087UK00M100-出货版_更新回收处理标志.indd 17

2019/10/22 16:18:02

«
...
15
16
17
18
19
...
»

Содержание 36087





































Отзывы:

Нет отзывов