manualshive.com logo in svg

Topcon GPT-7500 Series, Инструкция по эксплуатации

Поделиться
Скачать
Topcon GPT-7500 Series Скачать руководство пользователя страница 91

89

   6 CHECK AND ADJUSTMENT

•

H direction confirmation (Do not move V direction).

6

Turn the horizontal tangent screw, move the collimating point to the left side of prism gradually until 

buzzer sound stops.

7

Turn the horizontal tangent screw slowly, and move the collimating point to the prism center gradually 
until at the position buzzer starts.
Confirm the level of the signal (light quantity level) in display to adjust at the level of one to two as shown 
in below by turning the horizontal tangent screw.

8

Note the horizontal angle displayed. 

9

Turn the horizontal tangent screw, move the collimating point to the right side of prism gradually until 
buzzer sound stops.

10

Move the collimating point to the center of prism gradually until buzzer sound starts.
Turning the horizontal tangent screw to be one to two level of SIG value to adjust the collimating point 
same as step 7 procedure.

11

Note horizontal angle same as step 8 procedure.

Reticle

Prism

Prism

Reticle

Quantity level two

Reticle

Prism

Содержание GPT-7500 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды