Toolway TWXpert 105718 Скачать руководство пользователя страница 14

14

For Customer Assistance: Toll Free: 1-(800)-705-4454

email: [email protected] | website: www.toolway.com

6.0 MAINTENANCE

6.1  Clean the rope grab and lifeline with water and a mild soap solution. Wipe off hardware with a clean, dry cloth, 

and hang to air dry. Do not force dry with heat. An excessive buildup of dirt, paint, etc. may prevent the rope 

grab or lifeline from working properly, and in severe cases degrade the rope grab or rope to a point where it 

has weakened and should be removed from service. If you have any questions concerning the condition of the 

rope grab or lifeline, or have any doubt about putting them into service, contact TOOLWAY. See the Lifeline 

User Instruction Manual for specific maintenance details.

6.2  Additional maintenance and servicing procedures (replacement parts) must be completed by a factory 

authorized service center. Authorization must be in writing. Do not attempt to disassemble the unit. See 

section 5.1 for inspection frequency.

6.3  Store the rope grab and lifeline in a cool, dry, clean environment out of direct sunlight. Avoid areas where 

chemical vapors may exist. Thoroughly inspect the rope grab and lifeline after any period of extended storage.

7.0  SPECIFICATIONS / PERFORMANCE DATA

7.1 MATERIALS:

 

Material

: All material used in construction is certified to be new and free from defects.

 

Construction

: Riveted and welded with hinged rope channel.

 

Material Type

:  

    

Rope Grab

: Body, hinge, cam, and attachment eye – High impact resistant steel

    

Fall Arrester

: 100% Polyester

7.2 PERFORMANCE:

 

Maximum Arresting Distance

: 1 meter (39 inch) when dynamically tested in accordance with CAN/ 

 

NOTE

: This does not include lifeline elongation.

 

Arrest Force

: Designed for 1,800 lbs. maximum arresting force

 

Maximum Capacity

: 141 kg or 310 lbs.

 

Requirements

: Meets applicable CAN/CSA Z259.2.5-2017 and applicable OSHA standards, including 1910.66.

 

Parking Feature

: Allows manual operation as required

7.3 LIFELINE SPECIFICATIONS: 

 

Lifeline Diameter

: 16mm (5/8 inch)

 

Material

: Polyester and polypropylene

 

Color

: White with orange or green marker yarns Construction: Three strand, right hand lay Hardness: 5-15 lbs

 

Linear Density

: 9.5 lbs/100 ft., nominal 

 

Tensile Strength

: 6,000 lbs (27.0 kNs) 

 

Certification

: CSA Z259.2.5-2017

TABLE 1 - LIFELINE ELONGATION

Lifeline Length ft. (m)

Lifeline

Material

25'

50'

75'

100'

150'

200'

250'

300'

(7.6 m)

(15.2 m)

(22.9 m)

(30.5 m)

(45.7 m)

(61.0 m)

(76.2 m)

(91.4 m)

5/8"

Polyester

Polypropylene

2.5'

5'

7.5'

10'

15'

20'

25'

30

(0.8 m)

(1.5 m)

(2.3 m)

(3.0 m)

(4.6 m)

(6.1 m)

(7.6 m)

(9.1 m)

Содержание TWXpert 105718



















Отзывы: