Page 5
INSTALLATION & ASSEMBLY
The air compressor should be turned off and
unplugged from the power source before any
maintenance is performed as well as the air
bled from the tank and the unit allowed time to
cool. Personal injuries could occur from moving
parts, electrical sources, compressed air or hot
surfaces.
Location of the Air Compressor
The air compressor should always be located
in a clean, dry, and well-ventilated environment.
The unit should have at minimum, 30cm of
space on each side. The air filter intake should
be free of any debris or obstructions. Check the
air filter on a daily basis to be sure it is clean and
in working order.
Grounding Instructions
This product should be grounded. In the event
of an electrical short circuit, grounding reduces
the risk of electric shock by providing an escape
wire for the electric current. This prod¬uct is
equipped with a cord having a grounding wire
with an appropriate grounding plug. The plug
must be plugged into an outlet that is prop¬erly
installed and grounded in accordance with
all local codes and ordinances. Check with a
qualified electrician or service personnel if these
instructions are not completely under¬stood
or if in doubt as to whether the tool is properly
grounded.
Improper installation of the grounding plug will
result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary,
do not connect the grounding wire to either
flat blade terminal. The wire with insula¬tion
having an outer surface that is green with or
with¬out yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman
if the grounding instructions are not completely
understood, or if in doubt as to whether the
product is properly grounded. Do not modify the
plug provided; if it will not fit the outlet, have the
proper outlet installed by a qualified electrician.
This product is for use on a circuit having a
nominal rating of 230 volts and is factory-
equipped with a specific electric cord and plug
to permit connection to a proper electric circuit.
Make sure that the product is connected to an
outlet having the same configuration as the plug.
No adapter should be used with this product. If
the product must be reconnected for use on a
different type of electric circuit, qualified service
personnel should make the reconnection.
Extension Cords
Make sure your extension cord is in good
condition. When using an extension cord, be
sure to use one heavy enough to carry the
current your product will draw. An undersized
cord will cause a drop in line voltage resulting in
loss of power and overheating.
Break in Procedures
No break in procedure is required by the user.
This product is factory tested to ensure proper
operation and performance. Compressor must
always be turned ON or OFF using pressure
switch. Never turn machine OFF or ON using
power source
DRAIN
5.
INSTALLATION & ASSEMBLY
The air compressor should be turned off and
unplugged from the power source before any
maintenance is performed as well as the air
bled from the tank and the unit allowed time to
cool. Personal injuries could occur from moving
parts, electrical sources, compressed air or hot
surfaces.
Location of the Air Compressor
The air compressor should always be located
in a clean, dry, and well-ventilated environment.
The unit should have at minimum, 30cm of
space on each side. The air filter intake should
be free of any debris or obstructions. Check the
air filter on a daily basis to be sure it is clean and
in working order.
Grounding Instructions
This product should be grounded. In the event
of an electrical short circuit, grounding reduces
the risk of electric shock by providing an escape
wire for the electric current. This prod¬uct is
equipped with a cord having a grounding wire
with an appropriate grounding plug. The plug
must be plugged into an outlet that is prop¬erly
installed and grounded in accordance with
all local codes and ordinances. Check with a
qualified electrician or service personnel if these
instructions are not completely under¬stood
or if in doubt as to whether the tool is properly
grounded.
Improper installation of the grounding plug will
result in a risk of electric shock. If repair or
replacement of the cord or plug is necessary,
do not connect the grounding wire to either
flat blade terminal. The wire with insula¬tion
having an outer surface that is green with or
with¬out yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman
if the grounding instructions are not completely
understood, or if in doubt as to whether the
product is properly grounded. Do not modify the
plug provided; if it will not fit the outlet, have the
proper outlet installed by a qualified electrician.
This product is for use on a circuit having a
nominal rating of 230 volts and is factory-
equipped with a specific electric cord and plug
to permit connection to a proper electric circuit.
Make sure that the product is connected to an
outlet having the same configuration as the plug.
No adapter should be used with this product. If
the product must be reconnected for use on a
different type of electric circuit, qualified service
personnel should make the reconnection.
Extension Cords
Make sure your extension cord is in good
condition. When using an extension cord, be
sure to use one heavy enough to carry the
current your product will draw. An undersized
cord will cause a drop in line voltage resulting in
loss of power and overheating.
Break in Procedures
No break in procedure is required by the user.
This product is factory tested to ensure proper
operation and performance. Compressor must
always be turned ON or OFF using pressure
switch. Never turn machine OFF or ON using
power source
DRAIN
5.
INSTALLATION & ASSEMBLY
